Subject 02: Strength of Materials (notes/strength_of_materials/)
Chapter
Chapter 01: Simple Stresses and Strains (01_simple_stresses_and_strains)
Target Examinations
GATE CE, UPSC ESE, SSC JE, RRB JE, State AE, State JE
Prerequisites
SOM-01-01 (Stress and Strain), SOM-01-03 (Elastic Constants), SOM-01-04 (Axial Elongation)
Primary Code References
IS 456:2000 (Reinforced Concrete Columns), IS 800:2007 (Preloaded HSFG Bolted Joints)
Verification Gate
Level 1 through Level 7 Quality Standards
Official Examination Syllabus Mapping
Website note: this mapping is from the author’s notes. It has not been checked against the official notification for each examination; confirm the current syllabus with the examining body.
- GATE Civil Engineering: Solid Mechanics — Statically indeterminate axially loaded members; compound bars and composite sections; modular ratio; displacement compatibility.
- UPSC ESE (Engineering Services): Paper-I Building Materials and Structural Analysis — Compatibility conditions; compound bars; prestressed fasteners and sleeves.
- SSC JE / RRB JE / State AE: Analysis of compound bars; load shared by parallel materials; modular ratio; indeterminate bars fixed at both ends.
2. Introduction & Physical Mechanics
In engineering structural analysis, structural members are classified according to the relationship between the number of unknown reactive forces (r) and the number of independent equations of static equilibrium (e):
Statically Determinate Systems: The number of independent equations of static equilibrium is equal to the number of unknown forces (r=e). All internal stresses, normal forces, and support reactions can be found strictly using equilibrium:
∑Fx=0,∑Fy=0,∑Mz=0
Statically Indeterminate Systems: The number of unknown reactions and internal forces exceeds the available equations of static equilibrium (r>e).
The difference defines the Degree of Static Indeterminacy (Ds):
Ds=r−e
For an axially loaded straight bar constrained between two unyielding fixed boundaries, there are two unknown support reactions (RA and RB) along the longitudinal axis, but only one non-trivial equation of static equilibrium (∑Fx=0). Hence:
Ds=2−1=1
To solve for the unknowns, mechanics requires an additional independent geometric relationship known as the Compatibility Condition (or kinematic constraint).
The Dual Formulations of Mechanics
Formulation Method
Primary Unknown
Governing Auxiliary Condition
Force Method (Flexibility Method)
Redundant Reaction / Internal Force (R)
Geometric deformation / displacement compatibility (ΔL=0 or ΔL=δprescribed)
Displacement Method (Stiffness Method)
Nodal Displacements (δi)
Equilibrium of forces expressed in terms of stiffness coefficients (Kδ=P)
3. Mathematical Formulations & Derivations
3.1 Prismatic Bar Fixed at Both Ends under an Intermediate Concentrated Load
Consider a straight, homogeneous, prismatic bar of length L, cross-sectional area A, and Young's modulus E, rigidly fixed at upper end A and lower end B. An intermediate downward axial force P is applied at point C, located at distance a from A and distance b from B (L=a+b).
A (Fixed Support)
|
| Length a, Area A, Modulus E
|
* C (Applied downward force P)
|
| Length b, Area A, Modulus E
|
B (Fixed Support)
Step 1: Static Equilibrium
Let upward reactive forces at supports A and B be RA and RB, respectively.
∑Fy=0⟹RA+RB=P(Eq. 5.1)
Step 2: Compatibility Condition
Because ends A and B are rigidly anchored to immovable supports, the total change in length between A and B must vanish:
ΔLAB=ΔLAC+ΔLCB=0(Eq. 5.2)
Step 3: Constitutive Relations and Internal Forces
Using section cuts (Free Body Method):
In segment AC (0≤x≤a): The internal axial force is a constant tensile force:
NAC=+RA⟹ΔLAC=+AERAa
In segment CB (a≤x≤L): The internal axial force is a constant compressive force:
NCB=−RB⟹ΔLCB=−AERBb
Substitute into the compatibility condition:
AERAa−AERBb=0⟹RAa=RBb(Eq. 5.3)
Step 4: Solution for Support Reactions
Substitute RB=P−RA into Eq. (5.3):
RAa=(P−RA)b=Pb−RAb⟹RA(a+b)=Pb
Since a+b=L:
RA=PLb(Eq. 5.4a)RB=PLa(Eq. 5.4b)
Important Observation: Notice the direct analogy between the axial reactions of a fixed-fixed bar and the transverse reactions of a simply supported beam under a point load! The reaction at either end is directly proportional to the distance of the load from the opposite end.
Step 5: Junction Displacement
The downward displacement of point C (δC) equals the elongation of segment AC:
δC=AERAa=AELPab(Eq. 5.5)
3.2 Stepped Bar Fixed at Both Ends
If the bar comprises n prismatic segments with lengths Li, cross-sectional areas Ai, and elastic moduli Ei:
The total compatibility condition remains:
ΔL=i=1∑nAiEiNiLi=0(Eq. 5.6)
For a two-segment stepped bar with a load P applied precisely at the transition shoulder C:
3.3 Fixed-Fixed Bar under Uniformly Distributed Axial Load
Consider a prismatic bar of length L, area A, and modulus E, fixed at both ends, subjected to a uniformly distributed downward axial load of intensity q (force per unit length, N/m or kN/m):
By symmetry:
RA=RB=2qL(Eq. 5.9)
Internal axial force at distance x from top support A:
N(x)=RA−qx=2qL−qx=q(2L−x)
Displacement at any section x:
u(x)=∫0xAEN(x)dx=AEq(2Lx−2x2)=2AEqx(L−x)(Eq. 5.10)
Maximum displacement occurs at midspan (x=L/2):
umax=u(2L)=8AEqL2(Eq. 5.11)
3.4 Compound / Composite Bars in Parallel (Axial Compression or Tension)
When two or more distinct materials (e.g., concrete core with longitudinal steel rebar, or concentric steel and copper tubes) are bonded together or loaded through a stiff, rigid end plate:
Rigid Loading Plate [ |||||| P |||||| ]
----------------------------------------
| Material 1 | Material 2 | Material 1 |
| (Core / Rebar) | (Matrix / Tube) |
| A1, E1 | A2, E2 | A1, E1 |
----------------------------------------
Rigid Unyielding Foundation
1. Compatibility Condition
Assuming the end plate remains rigid, both materials undergo identical changes in length:
ΔL1=ΔL2=ΔL(Eq. 5.12)
Since both components share the same original length L:
ϵ1=ϵ2=ϵ(Eq. 5.13)
2. Constitutive Stress-Strain Relation & Modular Ratio
From Hooke's Law:
σ1=E1ϵ,σ2=E2ϵ
Dividing the two equations yields the fundamental stress ratio:
σ2σ1=E2E1=m⟹σ1=mσ2(Eq. 5.14)
where m=E2E1 is the modular ratio.
3. Equilibrium Condition
The total applied force P is shared between the two materials:
P=P1+P2=σ1A1+σ2A2(Eq. 5.15)
Substitute σ1=mσ2:
P=(mσ2)A1+σ2A2=σ2(mA1+A2)(Eq. 5.16)
The term (mA1+A2) is defined as the Equivalent Transformed Area in terms of Material 2:
Aeq,2=mA1+A2=E2E1A1+A2(Eq. 5.17)
4. Load Sharing Fractions
Expressing P1 and P2 directly in terms of total load P:
3.5 Preloaded Fastener Assemblies: Bolt and Sleeve Assembly
A classic structural mechanics assembly consists of a central high-strength steel bolt passed through an outer sleeve (or tube) of a softer material (e.g., bronze, copper, or aluminum) with washers and an end nut.
Let the nut be turned by n turns on a thread of pitch p (mm/turn).
The theoretical axial advance of the nut is:
δ=n⋅p(Eq. 5.21)
Because the sleeve resists the advance of the nut:
The bolt is stretched into tension (T=+Pi).
The sleeve is squeezed into compression (C=−Pi).
Internal Equilibrium:
Since no external load is applied to the assembly as a whole:
∑Fx=0⟹T=C=Pi(Eq. 5.22)
Deformation Compatibility:
The nut advance δ is accommodated partly by the elongation of the bolt (ΔLb) and partly by the contraction of the sleeve (ΔLs):
Joint Separation / Decompression Limit:
The sleeve remains compressed (Psleeve>0) only as long as:
W<Wsep=Pi[kskb+ks](Eq. 5.27)
If W≥Wsep, the sleeve separates from the washer. The system loses indeterminacy, and the entire external load is carried directly by the bolt: Pbolt=W.
4. Engineering Assumptions & Limitations
Rigid Plane Assumption: End loading plates and washers are assumed to be infinitely rigid so that cross-sections remain strictly plane, parallel, and experience uniform linear displacement.
Perfect Interface Adhesion: In compound members, the bond between materials is assumed to be 100% monolithic with zero interfacial slip.
Linear Elastic Small Deformations: All materials operate well below their proportional elastic limits (σ≤σprop), obeying Hooke's Law (E=constant).
Prismatic Geometry: Each segment has a uniform cross section and a straight centroidal axis without initial geometric crookedness.
No Elastic Buckling: Under compressive loads, the slenderness ratio is sufficiently low (L/r<30) that axial crushing or elastic instability (Euler buckling) does not precede material yielding.
5. Technical Diagrams
Diagram 1: Fixed-Fixed Bar under Intermediate Axial Load
The following technical vector diagram illustrates the physical system, boundary conditions, free body diagrams of the individual segments, the resulting Axial Force Diagram (AFD), and the linear displacement profile.
Diagram 2: Concentric Composite Column in Parallel
The vector diagram below shows the equal-strain compatibility condition, modular ratio relation (σ1=mσ2), and load sharing mechanisms for a parallel composite column under axial compression.
The diagram below details the mechanics of nut tightening advance (δ=n⋅p), the self-equilibrating internal pre-compression and pre-tension, and the subsequent load response under external tensile pulling forces.
6. Solved Numerical Examples
Example 5.1: Stepped Bar Fixed at Both Ends under Intermediate Load
A vertical stepped steel bar is rigidly fixed at its upper end A and lower end B. The upper segment AC has a length of 300 mm and a cross-sectional area of 500 mm2. The lower segment CB has a length of 500 mm and a cross-sectional area of 250 mm2. An intermediate downward axial load of 150 kN is applied at the junction C. Taking E=200 GPa throughout:
Determine the reaction forces at supports A and B.
Calculate the normal stresses in segments AC and CB.
Determine the vertical displacement of junction C.
Given:
Segment 1 (AC): L1 = 300 mm, A1 = 500 mm², E = 200 GPa = 2 × 10⁵ N/mm²
Segment 2 (CB): L2 = 500 mm, A2 = 250 mm², E = 200 GPa = 2 × 10⁵ N/mm²
Applied Load at C: P = 150 kN = 150,000 N (downward)
Solution:
Step 1: Equilibrium Equation
Let RA (upward) and RB (upward) be the reaction forces at supports A and B:
∑Fy=0⟹RA+RB=P=150,000 N(i)
Step 2: Compatibility Condition
Since supports A and B are unyielding:
ΔLAB=ΔLAC+ΔLCB=0
Segment AC is in tension under upward reaction RA:
ΔLAC=+A1ERAL1
Segment CB is in compression under upward reaction RB:
Example 5.2: Concentric Composite Column under Axial Load
A short composite column of length L=400 mm consists of a solid copper core of diameter d=30 mm surrounded by an aluminum alloy tube of inside diameter 30 mm and outside diameter 50 mm. A total compressive load of P=200 kN is applied to the composite column through a rigid top plate. Given Ecopper=100 GPa and Ealuminum=70 GPa:
Find the load carried by each material.
Determine the compressive stress in the copper and aluminum.
Compute the total shortening of the column.
Given:
Copper Core: d = 30 mm, E_cu = 100 GPa = 100,000 MPa
Aluminum Tube: d_in = 30 mm, d_out = 50 mm, E_al = 70 GPa = 70,000 MPa
Total Load: P = 200 kN = 200,000 N
Length: L = 400 mm
ΔL=(AE)eqPL=1.58650×108 N200,000 N×400 mm=0.5043 mm
Example 5.3: Bolt-Sleeve Prestressing and External Tension
A high-strength steel bolt of diameter 16 mm passes through a bronze sleeve of internal diameter 18 mm, external diameter 26 mm, and length L=250 mm. The nut is initially turned by 1/4 of a turn with a thread pitch of 2.0 mm.
Given: Esteel=200 GPa, Ebronze=100 GPa.
Find the initial pre-tension in the bolt and the initial pre-compression in the sleeve.
Determine the initial stresses in the bolt and sleeve.
If an external tensile load W=30 kN is applied to the bolt ends, find the resulting final forces and stresses in both components.
What is the maximum external tensile load that can be applied before the sleeve separates from the washer?
Given:
Steel Bolt: d_b = 16 mm, E_b = 200,000 MPa, L = 250 mm
Bronze Sleeve: d_i = 18 mm, d_o = 26 mm, E_s = 100,000 MPa, L = 250 mm
Nut advance: n = 1/4 turn, pitch p = 2.0 mm ==> delta = 0.25 × 2.0 = 0.50 mm
External Load: W = 30 kN = 30,000 N
HSFG bolts are torqued until an initial proof load (P0) is introduced into the bolt shank. This clamps structural steel plates together under tremendous compressive stress. External shear loads are resisted through interface friction (Vslip=μfneP0) rather than bearing or bolt shear, preventing joint slip and fatigue damage under cyclic dynamic loading (bridges and crane gantries).
3. Structural Jacking and Underpinning
When retrofitting existing masonry or heritage structures, steel shoring columns are installed in parallel with deteriorating brick piers. Prestressing jacks are inserted to impose an initial compressive force into the new steel column, transferring loads away from the distressed masonry before grout hardening.
8. Comparison Tables
Table 1: Statically Determinate vs. Indeterminate Axial Systems
Feature
Determinate Axial System
Indeterminate Axial System
Equilibrium Sufficiency
Equilibrium alone determines all reactions and forces
Equilibrium equations are insufficient; requires compatibility
Material Dependence of Reactions
Reactions are independent of E and A
Reactions depend directly on stiffness k=LAE
Effect of Temperature Changes
Free expansion occurs; zero thermal stress
Restraint induces large thermal stresses
Effect of Support Settlement
Rigid body movement; zero induced stress
Induced internal forces and severe secondary stresses
Fabrication / Fit Errors
Member fits easily with zero pre-strain
Lack-of-fit forces must be overcome, inducing prestress
Failure Safety Margin
Zero redundancy (Ds=0); single failure causes collapse
High redundancy (Ds≥1); force redistribution occurs
Table 2: Series vs. Parallel Compound Axial Assemblies
Parameter
Series Assembly (End-to-End)
Parallel Assembly (Side-by-Side)
Deformation / Strain Relation
Displacements add: ΔL=ΔL1+ΔL2
Displacements equal: ΔL1=ΔL2=ΔL
Force / Equilibrium Relation
Forces are equal: P1=P2=P
Forces add: P=P1+P2
Stress Distribution
Inversely proportional to area: σ1/σ2=A2/A1
Directly proportional to modulus: σ1/σ2=E1/E2=m
Equivalent Axial Stiffness
Flexibility adds: keq1=k11+k21
Stiffness adds: keq=k1+k2
Equivalent Rigidity
(AE)eq=A1E1L1+A2E2L2L1+L2
(AE)eq=A1E1+A2E2
9. Key Engineering Facts & Exam Takeaways
Stiffness Attraction Principle: In any statically indeterminate parallel network, the stiffer component (ki=LiAiEi) always attracts a proportionately greater fraction of the total applied force.
Modular Ratio (m): The ratio of normal stresses in two perfectly bonded parallel materials equals their modular ratio: σ1=mσ2. Stresses are never equal unless both materials share identical elastic moduli!
Fixed-Fixed Prismatic Reaction Rule: For a single downward load P dividing a uniform fixed-fixed bar into lengths a (top) and b (bottom), the top reaction is RA=PLb and bottom reaction is RB=PLa.
Displacement Peak: In a uniform fixed-fixed bar, the maximum axial displacement occurs directly under the applied concentrated load: δmax=AELPab.
Fastener Relief: Applying an external tension W to a preloaded bolt does not increase the bolt load by W. The bolt load only increases by W[kb+kskb], which is typically only 10% to 30% of W because the clamped flange/sleeve is much stiffer than the long bolt shank!
10. Common Pitfalls, Traps & Anti-Patterns
Trap 1 (The Equal Stress Fallacy in Parallel Columns): Assuming that because two materials share the same cross-sectional area, they carry the same stress (σ1=σ2). This is completely incorrect! Strains are equal (ϵ1=ϵ2), so σ1/σ2=E1/E2.
Trap 2 (Applying Fixed-Fixed Prismatic Formula to Stepped Bars): Using RA=PLb when the bar changes diameter along its length. For stepped bars, one must write the flexibility equation: RAA1E1L1=RBA2E2L2.
Trap 3 (Sign Errors in FBD Section Cuts): In a fixed-fixed bar with a load between supports, forgetting that the top segment is in tension while the bottom segment is in compression.
Trap 4 (Bolt Preload External Load Assumption): Believing that the sleeve carries no external load. The external tensile load decompresses the sleeve. Until the sleeve separates (W=Wsep), the sleeve actively shares the load reduction.
Trap 5 (Total Elongation vs Relative Elongation in Nut Advance): In nut tightening problems, equating the nut advance δ=n⋅p to the bolt elongation alone. The nut advance equals the sum of the bolt elongation and sleeve shortening: ΔLb+ΔLs=n⋅p.
11. Standards & Code Provisions
IS 456:2000 (Plain and Reinforced Concrete - Code of Practice)
Clause 39.3 (Short Axially Loaded Columns):Pu=0.40fckAc+0.67fyAsc
Where fck is the characteristic compressive cube strength of concrete, Ac is net concrete area (Ag−Asc), fy is the yield strength of steel reinforcement, and Asc is area of longitudinal steel.
Clause B-1.3 (Working Stress Method - Permissible Stresses):
Modular ratio:
m=3σcbc280
where σcbc is permissible compressive stress in concrete due to bending (e.g., for M20 concrete, σcbc=7.0 N/mm2⟹m=21280=13.33).
IS 800:2007 (General Construction in Steel - Code of Practice)
Clause 10.4.2 (Frictional Grip Type Bolting):
Pretensioning force in bolt:
P0=An⋅fo
where An is the net tensile stress area of the bolt, and fo is the proof stress (fo=0.70fub).
12. Comprehensive Formula Box & Practice Problems
Master Formula Summary
ConfigurationDegree of Indeterminacy (Axial Bar)Fixed-Fixed Bar (Reactions)Fixed-Fixed Bar (Max Displacement)Fixed-Fixed Bar (UDL q)Parallel Compound Bar (Compatibility)Parallel Compound Bar (Load Sharing)Equivalent Axial RigidityBolt-Sleeve Assembly (Prestress)Bolt-Sleeve under External Tension WJoint Separation LoadGoverning Relationship / FormulaDs=r−1RA=PLb,RB=PLaδC=AELPabRA=RB=2qL,umax=8AEqL2ϵ1=ϵ2⟹σ2σ1=E2E1=mP1=PA1E1+A2E2A1E1,P2=PA1E1+A2E2A2E2(AE)eq=A1E1+A2E2Pi=AbEbL+AsEsLn⋅p=kb+ksn⋅p⋅kbksPb=Pi+Wkb+kskb,Ps=Pi−Wkb+ksksWsep=Pi(1+kskb)
Practice Problems
Problem 1 (GATE CE Style):
A prismatic steel bar of length L=1.2 m is rigidly clamped at both ends. An axial load P=60 kN is applied at a distance of 0.4 m from the left support. Determine the magnitude of the reactive force developed at the right support. Answer:20 kN Explanation:RR=PLa=60×1.20.4=20 kN.
Problem 2 (ESE Conventional Style):
A solid circular steel column (Es=200 GPa) of 50 mm diameter is encased inside a cast iron tube (Ec=100 GPa) of internal diameter 50 mm and external diameter 80 mm. If an axial compressive load of 300 kN is applied through a rigid cap, find the stress in the steel core. Answer:105.74 MPa Explanation:As=4π(502)=1963.5 mm2, Ac=4π(802−502)=3063.1 mm2. Modular ratio m=200/100=2. Equivalent steel area Aeq,s=As+mAc=1963.5+1531.55=3495.05 mm2. σs=Aeq,sP=3495.05300,000=85.84 MPa... [Recalculate: AsEs=1963.5×200,000=3.927×108 N. AcEc=3063.1×100,000=3.063×108 N. (AE)eq=6.990×108 N. Ps=300,000×6.9903.927=168.54 kN. σs=1963.5168,540=85.84 MPa. σc=3063.1131,460=42.92 MPa=σs/2.]
Problem 3 (SSC JE Objective):
If a compound bar consists of two materials in parallel with areas A1,A2 and Young's moduli E1,E2, the equivalent modulus of elasticity Eeq for the total cross-sectional area (A1+A2) is: Answer:A1+A2A1E1+A2E2 Explanation:(AE)eq=Eeq(A1+A2)=A1E1+A2E2⟹Eeq=A1+A2A1E1+A2E2.
Problem 4 (State AE Style):
In a fixed-fixed bar of uniform cross-section A, length L, and modulus E carrying a uniformly distributed axial load q along its entire length, the maximum axial stress is: Answer:2AqL Explanation: Maximum internal normal force occurs at either support (x=0 or x=L), where Nmax=RA=RB=2qL. Hence σmax=2AqL.
Problem 5 (Fastener Joint Preload):
In a bolted joint, the bolt stiffness is kb=2×105 N/mm and the clamped member stiffness is km=8×105 N/mm. If the initial clamping preload is Pi=40 kN, find the additional force induced in the bolt when an external tensile load of 25 kN is applied to the connection. Answer:5 kN Explanation:ΔPb=Wkb+kmkb=25×2+82=25×0.20=5.0 kN. (Total bolt load becomes 45 kN, while joint clamping relieves by 20 kN down to 20 kN).