STEEL-05-03 Chapter 05 · Plate Girders

Plate Girder Stiffeners, End Panel Design & Splices (IS 800:2007 Cl. 8.7 & Cl. 10.3)

In this chapter (4 topics)
On this page
  1. 1. Executive Summary & Code Hierarchy
  2. 2. Classification & Structural Function of Stiffeners
  3. 3. Intermediate Transverse Stiffeners: Rigidity, Outstand & Strut Design
  4. 3.1 Minimum Second Moment of Area Is (IS 800:2007 Cl. 8.7.2.4)
  5. 3.2 Outstand Limitations (Cl. 8.7.1.2)
  6. 3.3 Strut Column Buckling Check (Cl. 8.7.2.4)
  7. 3.4 Connection to Web (IS 800 Cl. 8.7.2.6)
  8. 4. Bearing and Load-Carrying Stiffeners (IS 800 Cl. 8.7.3 & Cl. 8.7.4)
  9. 4.1 Direct Bearing on Flange (Web Crippling Check)
  10. 4.2 Column Buckling Capacity of Bearing Stiffener
  11. 5. Longitudinal (Horizontal) Stiffeners (IS 800 Cl. 8.7.1)
  12. 5.1 First Longitudinal Stiffener (at 0.20 d)
  13. 5.2 Second Longitudinal Stiffener (at 0.50 d)
  14. 6. End Panel Boundary Architecture: Rigid vs Non-Rigid End Posts
  15. 6.1 Non-Rigid End Post (Simple Post-Critical)
  16. 6.2 Rigid End Post (Twin Stiffeners)
  17. 7. Plate Girder Splices: Flange & Web Joints
  18. 7.1 Flange Splice Design (IS 800 Cl. 10.3)
  19. 7.2 Web Splice Design (IS 800 Cl. 10.3)
  20. 7.3 Golden Practical Rule: Staggering of Splices
  21. 8. SVG Engineering Visualizations
  22. FIGURE STEEL-05-03A: Stiffener Systems & Strut Column Sections
  23. FIGURE STEEL-05-03B: Flange & Web Splice Detailing & Vector Mechanics
  24. 9. Complete Step-by-Step Mathematical Derivations
  25. Derivation 1: Minimum Second Moment of Area Is for Transverse Stiffeners
  26. Derivation 2: Polar Modulus & Resultant Bolt Force in Web Splice
  27. 10. Multi-Exam Comprehensive Solved Examples
  28. Example 1: Design of Intermediate Transverse Stiffeners & Strut Check (GATE CE / ESE Conventional)
  29. Example 2: Design of End Bearing Stiffener at Support
  30. Example 3: Flange and Web Splice Design
  31. 11. Exam Traps, Common Pitfalls & Practical Fabrication Rules
  32. Trap 1: Confusing Intermediate Stiffener Rigidity with Strength
  33. Trap 2: Neglecting the Web Strip in Stiffener Column Checks
  34. Trap 3: Position of Longitudinal Stiffeners
  35. Trap 4: Direct Bearing Contact Snip
  36. Trap 5: Aligning Flange and Web Splices
  37. 12. Official Exam Practice Questions
  38. Question 1 (GATE CE)
  39. Question 2 (UPSC ESE)
  40. Question 3 (SSC JE)
  41. Question 4 (State AE)
  42. Question 5 (UPSC ESE Conventional)

1. Executive Summary & Code Hierarchy

In deep welded plate girders where the web slenderness ratio exceeds the limits of unstiffened serviceability (d/tw>67ϵd/t_w > 67\epsilon), the web plate cannot resist modern heavy railway and highway bridge loadings without specialized secondary stabilizing elements called stiffeners. Stiffeners are structural plates, angles, or rolled sections welded or bolted to the web plate to prevent out-of-plane buckling, ensure load dispersion, anchor post-buckling tension fields, and preserve cross-sectional geometry.

The design of plate girder stiffeners and field splices is governed by strict statutory specifications:

  • IS 800:2007 (Section 8.7 & Section 10.3): Indian Standard General Construction in Steel — Code of Practice (Third Revision).
  • IRC:24-2010: Standard Specifications and Code of Practice for Road Bridges — Steel Road Bridges.
  • IRS (Indian Railway Standard) Steel Bridge Code: Mandating dynamic impact factors and fatigue life checks.
  • Eurocode 3 (EN 1993-1-5): Plated structural elements.
  • AISC 360-16 (Chapter G & Chapter J): Specification for Structural Steel Buildings.

In addition to stiffener detailing, long-span plate girders (typically exceeding 18 m to 24 m18\text{ m to }24\text{ m}) cannot be transported from steel fabrication yards to the construction site in single pieces due to transportation clearances and vehicular payload limits. Consequently, they require field splices for both flanges and webs. Splicing high-capacity bridge girders demands rigorous limit-state detailing: flange splices must transmit massive tensile/compressive chord forces across joint gaps, while web splices must resist concurrent vertical shear and bending moment without slipping or overstressing fasteners.

┌───────────────────────────────────────────────────────────────────────────────────┐
│                     STIFFENER HIERARCHY (IS 800:2007 Cl. 8.7)                     │
├───────────────────────────────────────────────────────────────────────────────────┤
│ 1. Intermediate Transverse Stiffeners (Cl. 8.7.2):                                │
│    - Prevent shear buckling by subdividing web into panels of aspect ratio c/d.   │
│    - Act as compression struts anchoring post-buckling Tension Field Action (TFA).│
│                                                                                   │
│ 2. Bearing / Load-Carrying Stiffeners (Cl. 8.7.3 & 8.7.4):                        │
│    - Prevent web crippling (local crushing) and web buckling at supports/loads.   │
│    - Ground to direct bearing contact against flanges; designed as columns.       │
│                                                                                   │
│ 3. Longitudinal (Horizontal) Stiffeners (Cl. 8.7.1):                              │
│    - 1st Stiffener at 0.20 d from compression flange (prevents bending buckling).  │
│    - 2nd Stiffener at Neutral Axis (0.50 d) (mandatory when d/tw > 400ε).         │
│                                                                                   │
│ 4. End Panel Anchors: Rigid End Post vs Non-Rigid End Post (Cl. 8.5.3).           │
└───────────────────────────────────────────────────────────────────────────────────┘

2. Classification & Structural Function of Stiffeners

Stiffeners in plate girders are classified by their physical orientation and structural role:

  1. Intermediate Transverse Web Stiffeners (Vertical):

    • Welded perpendicular to the girder axis across the full or partial depth of the web.
    • They divide a long flexible web into short panels of width cc, drastically increasing the critical elastic shear buckling stress τcr\tau_{cr} by raising the shear buckling coefficient kvk_v.
    • When Tension Field Action develops, they act as vertical compression struts in an equivalent Pratt truss, resisting vertical force components FqF_q.
  2. Load-Carrying and Bearing Stiffeners (Support / Concentrated Load):

    • Positioned at locations of concentrated loads and reactions (e.g., bridge abutments, pier bearings, column junctions).
    • They transfer heavy vertical forces directly into the support without permitting localized web crushing (web crippling) or column buckling of the unstiffened web plate.
  3. Longitudinal (Horizontal) Stiffeners:

    • Welded parallel to the longitudinal axis of the girder on the web.
    • When a deep girder bends, the web above the neutral axis is subjected to compressive bending stresses σb\sigma_b. If d/tw>200ϵd/t_w > 200\epsilon, this zone will buckle elastically out of plane.
    • Placing a longitudinal stiffener at 0.20d0.20 d from the compression flange creates a nodal line of zero out-of-plane displacement, effectively increasing the bending buckling strength by over 300%300\%.
  4. Torsional / End Diagonal Stiffeners:

    • Provided at bearings to prevent the girder from twisting or rolling over at the supports (providing torsional restraint as required by IS 800 Table 15).

3. Intermediate Transverse Stiffeners: Rigidity, Outstand & Strut Design

3.1 Minimum Second Moment of Area IsI_s (IS 800:2007 Cl. 8.7.2.4)

To ensure that an intermediate transverse stiffener remains rigid and creates a true nodal line during web buckling, it must possess a minimum moment of inertia IsI_s about the centerline of the web:

Is≥0.75⋅d⋅tw3for cd≤2≈1.414Is≥1.5⋅d3⋅tw3c2for cd>2≈1.414\begin{aligned} I_s &\ge 0.75 \cdot d \cdot t_w^3 \quad \text{for } \frac{c}{d} \le \sqrt{2} \approx 1.414 \\ I_s &\ge \frac{1.5 \cdot d^3 \cdot t_w^3}{c^2} \quad \text{for } \frac{c}{d} > \sqrt{2} \approx 1.414 \end{aligned}

where:

  • dd is the clear depth of the web between flanges.
  • twt_w is the web thickness.
  • cc is the spacing between adjacent transverse stiffeners.

Note on calculation: For a pair of flat stiffeners of outstand bsb_s and thickness tqt_q welded symmetrically on both sides of the web, the total width across the web is 2bs+tw2 b_s + t_w. The moment of inertia about the center of the web is:

Iprovided=tq(2bs+tw)312I_{provided} = \frac{t_q (2 b_s + t_w)^3}{12}

3.2 Outstand Limitations (Cl. 8.7.1.2)

To prevent local torsional buckling of the stiffener plate itself before it mobilizes its full strength:

  • For flat stiffeners (unstiffened outstand): bs≤14⋅tq⋅ϵb_s \le 14 \cdot t_q \cdot \epsilon
  • For angle or tee sections (stiffened outstand): bs≤20⋅tq⋅ϵb_s \le 20 \cdot t_q \cdot \epsilon

where ϵ=250/fy\epsilon = \sqrt{250 / f_y}. For Fe 410 steel (fy=250 MPaf_y = 250\text{ MPa}), ϵ=1.0\epsilon = 1.0.

3.3 Strut Column Buckling Check (Cl. 8.7.2.4)

When intermediate stiffeners are not subjected to concentrated external loads, they must still be checked as an axial compression member (strut) if Tension Field Action is mobilized in the web panels.

  1. Effective Column Section:

    • The effective column consists of the stiffener plates plus an effective strip of web of width 20tw20 t_w (10tw10 t_w on each side of the stiffener centerline, or 10tw10 t_w total if at an edge).
    Aeff=2(bs⋅tq)+(20tw⋅tw)A_{eff} = 2 (b_s \cdot t_q) + (20 t_w \cdot t_w)
  2. Effective Length:

    KL=0.70⋅dKL = 0.70 \cdot d

    (The flanges provide rotational and lateral restraint at the top and bottom).

  3. Design Compressive Strength PdP_d:

    λ=KLreffwhere reff=IeffAeff\lambda = \frac{KL}{r_{eff}} \quad \text{where } r_{eff} = \sqrt{\frac{I_{eff}}{A_{eff}}}

    The design compressive stress fcdf_{cd} is obtained from Buckling Curve c (α=0.49\alpha = 0.49) per IS 800 Cl. 7.1.2.1:

    Pd=Aeff⋅fcdP_d = A_{eff} \cdot f_{cd}
  4. Design Axial Force FqF_q from Tension Field Action:

    Fq=V−Vcrγm0≥0F_q = V - \frac{V_{cr}}{\gamma_{m0}} \ge 0

    where VV is the maximum design shear force in the adjacent panels, and VcrV_{cr} is the simple post-critical shear buckling strength. The stiffener is safe if:

    Fq≤PdF_q \le P_d

3.4 Connection to Web (IS 800 Cl. 8.7.2.6)

Intermediate transverse stiffeners must be connected to the web by welds designed to resist a minimum shear force per unit length:

qw≥tw25bs(kN/mm)q_w \ge \frac{t_w^2}{5 b_s} \quad (\text{kN/mm})

where twt_w and bsb_s are in mm. Furthermore, transverse stiffeners not subjected to external loads may stop short of the tension flange by a distance not exceeding 4tw4 t_w to prevent fatigue cracking of the tension flange under cyclic loading.


4. Bearing and Load-Carrying Stiffeners (IS 800 Cl. 8.7.3 & Cl. 8.7.4)

At supports or under heavy concentrated wheel loads (e.g., gantry cranes), the web is subjected to massive compressive stresses that can cause instantaneous crushing (web crippling) or out-of-plane buckling.

4.1 Direct Bearing on Flange (Web Crippling Check)

Bearing stiffeners must be fitted tightly against the loaded flange (ground to direct bearing or connected by full-penetration butt welds). The design bearing capacity of the stiffener alone against the flange is given by:

Fpsd=Abr⋅fy0.8⋅γm0=1.136⋅Abr⋅fyF_{psd} = \frac{A_{br} \cdot f_y}{0.8 \cdot \gamma_{m0}} = 1.136 \cdot A_{br} \cdot f_y

where:

  • AbrA_{br} is the net contact bearing area between the stiffener and the flange plate.
  • To clear the continuous web-to-flange fillet welds, the inner corner of the stiffener plate must be snipped (coped) by a dimension cs≈15 to 20 mmc_s \approx 15\text{ to }20\text{ mm}.
  • For a pair of bearing stiffeners: Abr=2(bs−cs)tqA_{br} = 2 (b_s - c_s) t_q

4.2 Column Buckling Capacity of Bearing Stiffener

The assembly of bearing stiffeners and the web plate acts as a vertical compression member.

  • Effective Web Width: A width of web equal to 20tw20 t_w (10tw10 t_w on either side of the stiffener, or 10tw10 t_w total at the end of a cantilever or end support).
  • Effective Length: KL=0.70dKL = 0.70 d (when flanges are restrained against lateral translation and rotation).
  • Buckling Capacity: Sized to satisfy: Pd=Aeff⋅fcd≥RuP_d = A_{eff} \cdot f_{cd} \ge R_u where RuR_u is the factored support reaction.

5. Longitudinal (Horizontal) Stiffeners (IS 800 Cl. 8.7.1)

Longitudinal stiffeners are required when the web slenderness is high:

dtw>200ϵ  ⟹  1st Longitudinal Stiffener mandatory at 0.20ddtw>400ϵ  ⟹  2nd Longitudinal Stiffener mandatory at 0.50d (Neutral Axis)\begin{aligned} \frac{d}{t_w} &> 200\epsilon \implies \text{1st Longitudinal Stiffener mandatory at } 0.20 d \\ \frac{d}{t_w} &> 400\epsilon \implies \text{2nd Longitudinal Stiffener mandatory at } 0.50 d\text{ (Neutral Axis)} \end{aligned}
   COMPRESSION FLANGE
   ══════════════════════════════════════════════════════════
   │ ▲
   │ │  0.20 d  ──► 1st LONGITUDINAL STIFFENER (I_s1 ≥ 4 c tw³)
   │ ▼              (At centroid of flexural compressive stress)
   │ 
   │                2nd LONGITUDINAL STIFFENER (I_s2 ≥ c tw³)
   │ ─── 0.50 d ──► (At Neutral Axis - prevents shear buckling)
   │ 
   │
   │
   ══════════════════════════════════════════════════════════
   TENSION FLANGE

5.1 First Longitudinal Stiffener (at 0.20d0.20 d)

  • Location: Placed at a distance of 0.20d0.20 d from the inner face of the compression flange.
  • Structural Rationale: Under pure bending, compressive normal stress σb\sigma_b varies linearly from zero at the neutral axis (0.5d0.5 d) to maximum at the top edge (0.0d0.0 d). The resultant compressive force acts at one-third depth of the compression zone, which corresponds precisely to: 23×(0.50d)≈0.33d from NA  ⟹  0.50d−0.33d≈0.17d to 0.20d from flange\frac{2}{3} \times (0.50 d) \approx 0.33 d \text{ from NA} \implies 0.50 d - 0.33 d \approx 0.17 d \text{ to } 0.20 d \text{ from flange} Placing the stiffener at 0.20d0.20 d divides the compression zone into two panels: d1=0.20dd_1 = 0.20 d and d2=0.80dd_2 = 0.80 d. The sub-panel 0.20d0.20 d has a very small depth, preventing elastic flexural buckling.
  • Minimum Moment of Inertia (IS 800 Cl. 8.7.1.3): Is1≥4.0⋅c⋅tw3I_{s1} \ge 4.0 \cdot c \cdot t_w^3

5.2 Second Longitudinal Stiffener (at 0.50d0.50 d)

  • Location: Placed at the neutral axis (0.50d0.50 d).
  • Structural Rationale: Provides additional shear buckling resistance and prevents asymmetrical lateral buckling when d/twd/t_w approaches the statutory maximum ceiling of 400ϵ400\epsilon.
  • Minimum Moment of Inertia (IS 800 Cl. 8.7.1.4): Is2≥1.0⋅c⋅tw3I_{s2} \ge 1.0 \cdot c \cdot t_w^3

6. End Panel Boundary Architecture: Rigid vs Non-Rigid End Posts

Under IS 800:2007 Cl. 8.5.3, the end panel of a plate girder designed with Tension Field Action must anchor the horizontal component of the diagonal membrane tension HtfH_{tf}:

Htf=12fv⋅wtf⋅tw⋅cos⁡ϕH_{tf} = \frac{1}{2} f_v \cdot w_{tf} \cdot t_w \cdot \cos\phi

6.1 Non-Rigid End Post (Simple Post-Critical)

  • Consists of a single vertical bearing stiffener placed at the centerline of the support bearing.
  • The single stiffener has zero flexural rigidity in the longitudinal plane of the girder and cannot resist HtfH_{tf}.
  • Consequently, the end panel cannot develop Tension Field Action.
  • The end panel must be designed using the Simple Post-Critical Method (Vd=Vcr/γm0V_d = V_{cr} / \gamma_{m0}). Since maximum shear occurs at the support, the designer must either:
    1. Reduce stiffener spacing cc near the support (e.g., c=0.5dc = 0.5 d) to raise kvk_v and VcrV_{cr}.
    2. Increase the web plate thickness twt_w in the end panel.

6.2 Rigid End Post (Twin Stiffeners)

  • Fabricated using two vertical stiffeners spaced at a distance e≥0.10de \ge 0.10 d apart, connected by the web plate to form a closed vertical box or I-beam.
  • The rigid end post spans vertically as a beam between the top and bottom flanges (span length =d= d).
  • It resists the horizontal pull HtfH_{tf} through vertical beam bending.
  • The design bending moment in the rigid end post is: Mpost=Htf⋅d10M_{post} = \frac{H_{tf} \cdot d}{10}
  • Providing a rigid end post allows the end panel to develop full Tension Field Action (VtfV_{tf}), avoiding web thickening or congested stiffeners.

7. Plate Girder Splices: Flange & Web Joints

When girder spans exceed transportable lengths (L>18 m to 24 mL > 18\text{ m to }24\text{ m}), field splices are required.

                  FLANGE SPLICE
             ┌─────────────────────┐ Outer Splice Plate
             ▼                     ▼
       ════════════════════   ════════════════════
       ════════════════════   ════════════════════ Main Flange
             ▲                     ▲
             └─────────────────────┘ Inner Splice Plates (Straddling web)
                   │ Joint Gap (5-10 mm)
                   ▼
       ────────────────────   ────────────────────
       │                  │   │                  │
       │                  │   │                  │  WEB SPLICE:
       │    ┌───────────────────────┐            │  Double cover plates
       │    │   o   o   o │ o   o   │            │  resisting Vu & Mw
       │    │   o   o   o │ o   o   │            │
       │    │   o   o   o │ o   o   │            │
       │    └───────────────────────┘            │
       │                  │   │                  │
       ────────────────────   ────────────────────

7.1 Flange Splice Design (IS 800 Cl. 10.3)

  1. Design Force PfP_f: Standard code practice mandates that the flange splice be designed to transmit the full plastic tensile/compressive capacity of the flange:

    Pf=bf⋅tf⋅fyγm0P_f = \frac{b_f \cdot t_f \cdot f_y}{\gamma_{m0}}

    (Alternatively, the actual design force Pf=Mu/(d+tf)P_f = M_u / (d + t_f) may be used, provided it is not less than 0.750.75 of the full strength).

  2. Splice Plates:

    • An outer splice cover plate placed on the exterior face (bs1=bfb_{s1} = b_f).
    • Two inner splice plates placed on the interior face, straddling the web on each side of the fillet weld.
    • Total cross-sectional area: Asplice=(bs1⋅ts1)+2(bs2⋅ts2)≥bf⋅tfA_{splice} = (b_{s1} \cdot t_{s1}) + 2 (b_{s2} \cdot t_{s2}) \ge b_f \cdot t_f
  3. Fastener Design (Double Shear):

    • High-Strength Friction Grip (HSFG Class 8.8 or 10.9) bolts are preferred to prevent slip.
    • Number of bolts required on each side of the joint: n=PfVdsbn = \frac{P_f}{V_{dsb}} where VdsbV_{dsb} is the double-shear capacity per bolt.

7.2 Web Splice Design (IS 800 Cl. 10.3)

The web splice is placed at a section of low bending moment (e.g., quarter-span) and consists of two cover plates sandwiching the web plate (2×tsp≥tw2 \times t_{sp} \ge t_w).

  1. Applied Design Forces:

    • Factored vertical shear: VuV_u.
    • Bending moment carried by the web: Mw=(IwebItotal)MuM_w = \left(\frac{I_{web}}{I_{total}}\right) M_u
  2. Bolt Force Distribution (Vector Analysis):

    • On each side of the joint, an array of nn bolts in mm vertical rows is provided.
    • Direct vertical shear force per bolt: Fv=VunF_v = \frac{V_u}{n}
    • Torsional moment shear force on extreme bolt: Fm=Mw⋅rmax⁡∑ri2=Mw⋅rmax⁡∑(xi2+yi2)F_m = \frac{M_w \cdot r_{\max}}{\sum r_i^2} = \frac{M_w \cdot r_{\max}}{\sum (x_i^2 + y_i^2)} acting perpendicular to the radius vector rmax⁡r_{\max}.
    • Combined Resultant Shear Force on Critical Bolt: FR=Fv2+Fm2+2FvFmcos⁡θ≤VdsbF_R = \sqrt{F_v^2 + F_m^2 + 2 F_v F_m \cos\theta} \le V_{dsb} where θ\theta is the angle between the vectors F⃗v\vec{F}_v and F⃗m\vec{F}_m.

7.3 Golden Practical Rule: Staggering of Splices

NEVER SPLICE FLANGES AND WEBS AT THE SAME CROSS-SECTION. Splicing both flanges and the web in the same vertical plane creates a continuous weak discontinuity across the entire girder. Flange splices and web splices must be staggered longitudinally by at least 300 mm to 500 mm300\text{ mm to }500\text{ mm} (or separated by a full panel width).


8. SVG Engineering Visualizations

FIGURE STEEL-05-03A: Stiffener Systems & Strut Column Sections

The following technical drawing details the elevation of a deep plate girder showing intermediate, longitudinal, and bearing stiffeners, alongside the plan views of effective column strut sections.

Plate Girder Stiffeners Transverse Longitudinal and Bearing

FIGURE STEEL-05-03B: Flange & Web Splice Detailing & Vector Mechanics

The following engineering schematic illustrates the detailing of bolted flange and web splices, force transfer across cover plates, and the resultant shear force vector acting on the critical corner bolt.

Plate Girder Splices Flange and Web Detailing

9. Complete Step-by-Step Mathematical Derivations

Derivation 1: Minimum Second Moment of Area IsI_s for Transverse Stiffeners

Consider an infinitely long plate of width dd simply supported along its longitudinal edges (flanges), subjected to shear stress τ\tau. When transverse stiffeners are placed at spacing cc, they divide the plate into panels of aspect ratio α=c/d\alpha = c/d.

  1. For the stiffeners to enforce a pure nodal line (w=0w = 0 along the stiffener axis) during out-of-plane buckling, the flexural rigidity of the stiffener (EIs)(E I_s) must exceed the critical threshold derived by Timoshenko and Bryan:

    γ=EIsD⋅d≥γreq\gamma = \frac{E I_s}{D \cdot d} \ge \gamma_{req}

    where D=Etw312(1−μ2)D = \frac{E t_w^3}{12 (1 - \mu^2)} is the plate flexural rigidity.

  2. Empirical and theoretical energy solutions establish that for α=c/d≤2≈1.414\alpha = c/d \le \sqrt{2} \approx 1.414:

    γreq≈14(c/d)2−8\gamma_{req} \approx \frac{14}{(c/d)^2} - 8

    Substituting DD with μ=0.30\mu = 0.30 and introducing a factor of safety of 1.51.5 for limit-state compliance:

    Is≥0.75⋅d⋅tw3■I_s \ge 0.75 \cdot d \cdot t_w^3 \quad \blacksquare
  3. For wide panels where c/d>2c/d > \sqrt{2}, buckling initiates in higher order harmonics between stiffeners, scaling inversely with c2c^2:

    Is≥1.5⋅d3⋅tw3c2■I_s \ge \frac{1.5 \cdot d^3 \cdot t_w^3}{c^2} \quad \blacksquare

Derivation 2: Polar Modulus & Resultant Bolt Force in Web Splice

Consider a web splice connection with nn bolts subjected to a factored bending moment MwM_w and factored vertical shear VuV_u. The centroid of the bolt group is located at (xˉ,yˉ)=(0,0)(\bar{x}, \bar{y}) = (0, 0).

  1. The vertical shear load VuV_u is distributed uniformly among all nn bolts:

    F⃗v=(0,−Vun)\vec{F}_v = \left(0, -\frac{V_u}{n}\right)
  2. The moment MwM_w causes each bolt located at (xi,yi)(x_i, y_i) to exert a restoring couple. The shear force on bolt ii due to moment is proportional to its distance from the centroid ri=xi2+yi2r_i = \sqrt{x_i^2 + y_i^2}:

    Fmi=k⋅riF_{mi} = k \cdot r_i

    The total resisting moment is:

    ∑(Fmi⋅ri)=k∑ri2=Mw  ⟹  k=Mw∑ri2=MwIpg\sum (F_{mi} \cdot r_i) = k \sum r_i^2 = M_w \implies k = \frac{M_w}{\sum r_i^2} = \frac{M_w}{I_{pg}}

    where Ipg=∑(xi2+yi2)I_{pg} = \sum (x_i^2 + y_i^2) is the polar moment of inertia of the bolt group. The maximum force occurs on the bolt with maximum radius rmax⁡r_{\max}:

    Fm=Mw⋅rmax⁡IpgF_m = \frac{M_w \cdot r_{\max}}{I_{pg}}
  3. Vector F⃗m\vec{F}_m acts perpendicular to the radius vector r⃗max⁡\vec{r}_{\max}. The angle θ\theta between the downward vertical vector F⃗v\vec{F}_v and F⃗m\vec{F}_m is:

    cos⁡θ=xmax⁡rmax⁡\cos\theta = \frac{x_{\max}}{r_{\max}}

    The resultant shear force on the extreme critical bolt is obtained via the law of cosines:

    FR=Fv2+Fm2+2FvFmcos⁡θ≤Vdsb■F_R = \sqrt{F_v^2 + F_m^2 + 2 F_v F_m \cos\theta} \le V_{dsb} \quad \blacksquare

10. Multi-Exam Comprehensive Solved Examples

Example 1: Design of Intermediate Transverse Stiffeners & Strut Check (GATE CE / ESE Conventional)

Problem Statement: A plate girder has a clear web depth d=1500 mmd = 1500\text{ mm} and web thickness tw=8.0 mmt_w = 8.0\text{ mm} (fy=250 MPaf_y = 250\text{ MPa}). Intermediate transverse stiffeners are provided at c=1500 mmc = 1500\text{ mm} (c/d=1.0c/d = 1.0). At the section, the design shear force is V=850 kNV = 850\text{ kN} and the simple post-critical shear capacity is Vcr=524.45 kNV_{cr} = 524.45\text{ kN}.

  1. Determine the minimum required moment of inertia IsI_s per IS 800:2007.
  2. Select a suitable pair of flat stiffeners and verify the outstand limit.
  3. Check the stiffener as an axial strut under post-buckling Tension Field Action force FqF_q.

Solution:

Step 1: Minimum Second Moment of Area IsI_s

  • Aspect ratio: cd=15001500=1.0≤2≈1.414\frac{c}{d} = \frac{1500}{1500} = 1.0 \le \sqrt{2} \approx 1.414
  • Required IsI_s (IS 800 Cl. 8.7.2.4): Is,min⁡=0.75⋅d⋅tw3=0.75×1500×8.03=0.75×1500×512=576,000 mm4I_{s,\min} = 0.75 \cdot d \cdot t_w^3 = 0.75 \times 1500 \times 8.0^3 = 0.75 \times 1500 \times 512 = \mathbf{576,000\text{ mm}^4}

Step 2: Trial Stiffener Section & Outstand Check

  • Try a pair of flat stiffeners welded on opposite sides of the web:
    • Outstand width: bs=90 mmb_s = 90\text{ mm}
    • Thickness: tq=8.0 mmt_q = 8.0\text{ mm}
  • Outstand limit check (Cl. 8.7.1.2): ϵ=250250=1.0\epsilon = \sqrt{\frac{250}{250}} = 1.0 bs,max⁡=14⋅tq⋅ϵ=14×8.0×1.0=112 mmb_{s,\max} = 14 \cdot t_q \cdot \epsilon = 14 \times 8.0 \times 1.0 = 112\text{ mm} Since bs=90 mm≤112 mmb_s = 90\text{ mm} \le 112\text{ mm}, outstand is completely SAFE against local buckling.
  • Total width across the web: btot=2bs+tw=2(90)+8=188 mmb_{tot} = 2 b_s + t_w = 2(90) + 8 = 188\text{ mm}
  • Moment of inertia provided about the web centerline: Iprovided=tq⋅btot312=8.0×(188)312=8.0×6,644,67212=4,429,781 mm4I_{provided} = \frac{t_q \cdot b_{tot}^3}{12} = \frac{8.0 \times (188)^3}{12} = \frac{8.0 \times 6,644,672}{12} = \mathbf{4,429,781\text{ mm}^4}
  • Check rigidity: IprovidedIs,min⁡=4,429,781576,000=7.69≥1.0  ⟹  SAFE!\frac{I_{provided}}{I_{s,\min}} = \frac{4,429,781}{576,000} = 7.69 \ge 1.0 \implies \mathbf{SAFE!}

Step 3: Strut Column Buckling Check under TFA Force FqF_q

  • Effective column section (pair of flats + 20tw20 t_w web strip): bweb,eff=20⋅tw=20×8.0=160 mmb_{web,eff} = 20 \cdot t_w = 20 \times 8.0 = 160\text{ mm} Aeff=2(bs⋅tq)+(bweb,eff⋅tw)=2(90×8)+(160×8)=1440+1280=2720 mm2A_{eff} = 2 (b_s \cdot t_q) + (b_{web,eff} \cdot t_w) = 2(90 \times 8) + (160 \times 8) = 1440 + 1280 = \mathbf{2720\text{ mm}^2}
  • Moment of inertia of effective section about web axis: Ieff=Iprovided+bweb,eff⋅tw312=4,429,781+160×8312=4,429,781+6,827=4,436,608 mm4I_{eff} = I_{provided} + \frac{b_{web,eff} \cdot t_w^3}{12} = 4,429,781 + \frac{160 \times 8^3}{12} = 4,429,781 + 6,827 = 4,436,608\text{ mm}^4
  • Radius of gyration: reff=IeffAeff=4,436,6082720=1631.1=40.39 mmr_{eff} = \sqrt{\frac{I_{eff}}{A_{eff}}} = \sqrt{\frac{4,436,608}{2720}} = \sqrt{1631.1} = \mathbf{40.39\text{ mm}}
  • Effective length: KL=0.70⋅d=0.70×1500=1050 mmKL = 0.70 \cdot d = 0.70 \times 1500 = 1050\text{ mm}
  • Slenderness ratio: λ=KLreff=105040.39=26.00\lambda = \frac{KL}{r_{eff}} = \frac{1050}{40.39} = 26.00
  • Design compressive stress fcdf_{cd} (Buckling Curve c, α=0.49,fy=250 MPa\alpha = 0.49, f_y = 250\text{ MPa}):
    • Euler stress: fcc=π2×200000262=2920.1 MPaf_{cc} = \frac{\pi^2 \times 200000}{26^2} = 2920.1\text{ MPa}
    • Non-dimensional slenderness: λˉ=250/2920.1=0.293\bar{\lambda} = \sqrt{250 / 2920.1} = 0.293
    • ϕ=0.5[1+0.49(0.293−0.2)+0.2932]=0.5[1+0.0456+0.0858]=0.5657\phi = 0.5 [1 + 0.49(0.293 - 0.2) + 0.293^2] = 0.5 [1 + 0.0456 + 0.0858] = 0.5657
    • χ=10.5657+0.56572−0.2932=10.5657+0.484=0.953\chi = \frac{1}{0.5657 + \sqrt{0.5657^2 - 0.293^2}} = \frac{1}{0.5657 + 0.484} = 0.953
    • fcd=χfyγm0=0.953×2501.10=216.57 MPaf_{cd} = \frac{\chi f_y}{\gamma_{m0}} = \frac{0.953 \times 250}{1.10} = \mathbf{216.57\text{ MPa}}
  • Design axial compressive strength: Pd=Aeff⋅fcd=2720×216.57×10−3=589.08 kNP_d = A_{eff} \cdot f_{cd} = 2720 \times 216.57 \times 10^{-3} = \mathbf{589.08\text{ kN}}
  • Axial force to resist from Tension Field Action (noting Vcr=524.45 kNV_{cr} = 524.45\text{ kN} from Step 1 already incorporates γm0=1.10\gamma_{m0} = 1.10): Fq=V−Vcr=850.00−524.45=325.55 kNF_q = V - V_{cr} = 850.00 - 524.45 = \mathbf{325.55\text{ kN}}
  • Comparison: Fq=325.55 kN≤Pd=589.08 kN  ⟹  STRUT IS FULLY SAFE!F_q = 325.55\text{ kN} \le P_d = 589.08\text{ kN} \implies \mathbf{STRUT\ IS\ FULLY\ SAFE!}

Example 2: Design of End Bearing Stiffener at Support

Problem Statement: Design an end bearing stiffener for a plate girder supporting a factored reaction Ru=950 kNR_u = 950\text{ kN}. Web plate is 1500 mm×8.0 mm1500\text{ mm} \times 8.0\text{ mm} and flange plates are 450 mm×25 mm450\text{ mm} \times 25\text{ mm} (fy=250 MPa,fu=410 MPaf_y = 250\text{ MPa}, f_u = 410\text{ MPa}). Check direct bearing, column buckling, and weld connection to the web.

Solution:

Step 1: Stiffener Geometry Selection

  • Available width on either side of web: bavail=bf−tw2=450−82=221 mmb_{avail} = \frac{b_f - t_w}{2} = \frac{450 - 8}{2} = 221\text{ mm}
  • Adopt a pair of plates: bs=200 mmb_s = 200\text{ mm}, thickness tq=16 mmt_q = 16\text{ mm}.
  • Provide a snip (chamfer) of 15 mm15\text{ mm} to clear the web-to-flange fillet weld.
  • Outstand check: bs=200 mm≤14⋅tq⋅ϵ=14×16×1.0=224 mm  ⟹  SAFE!b_s = 200\text{ mm} \le 14 \cdot t_q \cdot \epsilon = 14 \times 16 \times 1.0 = 224\text{ mm} \implies \mathbf{SAFE!}

Step 2: Direct Flange Bearing Check (Cl. 8.7.4)

  • Net bearing contact area: Abr=2(bs−cs)tq=2(200−15)×16=2×185×16=5920 mm2A_{br} = 2 (b_s - c_s) t_q = 2 (200 - 15) \times 16 = 2 \times 185 \times 16 = \mathbf{5920\text{ mm}^2}
  • Design bearing capacity: Fpsd=Abr⋅fy0.8⋅γm0=5920×2500.8×1.10×103=1,480,0000.88=1681.82 kNF_{psd} = \frac{A_{br} \cdot f_y}{0.8 \cdot \gamma_{m0}} = \frac{5920 \times 250}{0.8 \times 1.10 \times 10^3} = \frac{1,480,000}{0.88} = \mathbf{1681.82\text{ kN}}
  • Check: Fpsd=1681.82 kN≥Ru=950.00 kN  ⟹  BEARING IS SAFE! (+77.0% margin)F_{psd} = 1681.82\text{ kN} \ge R_u = 950.00\text{ kN} \implies \mathbf{BEARING\ IS\ SAFE!\ (+77.0\%\ margin)}

Step 3: Column Buckling Check (Cl. 8.7.3)

  • Effective section: 2 stiffener plates + web strip of 20tw=20×8=160 mm20 t_w = 20 \times 8 = 160\text{ mm}. Aeff=2(200×16)+(160×8)=6400+1280=7680 mm2A_{eff} = 2(200 \times 16) + (160 \times 8) = 6400 + 1280 = \mathbf{7680\text{ mm}^2}
  • Total width across web: 2bs+tw=2(200)+8=408 mm2 b_s + t_w = 2(200) + 8 = 408\text{ mm}.
  • Moment of inertia: Ieff=16×(408)312+160×8312=90.56×106 mm4I_{eff} = \frac{16 \times (408)^3}{12} + \frac{160 \times 8^3}{12} = 90.56 \times 10^6\text{ mm}^4
  • Radius of gyration: reff=90.56×1067680=108.59 mmr_{eff} = \sqrt{\frac{90.56 \times 10^6}{7680}} = \mathbf{108.59\text{ mm}}
  • Effective length: KL=0.70⋅d=0.70×1500=1050 mmKL = 0.70 \cdot d = 0.70 \times 1500 = 1050\text{ mm}
  • Slenderness: λ=KLreff=1050108.59=9.67  ⟹  λˉ=250π2(200000)/9.672=0.1088≤0.20\lambda = \frac{KL}{r_{eff}} = \frac{1050}{108.59} = 9.67 \implies \bar{\lambda} = \sqrt{\frac{250}{\pi^2 (200000) / 9.67^2}} = 0.1088 \le 0.20
  • Per IS 800:2007 Clause 7.1.2.1, since λˉ≤0.20\bar{\lambda} \le 0.20, the stress reduction factor is capped at χ=1.00\chi = 1.00: fcd=χfyγm0=1.00×2501.10=227.27 MPaf_{cd} = \frac{\chi f_y}{\gamma_{m0}} = \frac{1.00 \times 250}{1.10} = \mathbf{227.27\text{ MPa}}
  • Compressive capacity: Pcd=Aeff⋅fcd=7680×227.273×10−3=1745.45 kNP_{cd} = A_{eff} \cdot f_{cd} = 7680 \times 227.273 \times 10^{-3} = \mathbf{1745.45\text{ kN}}
  • Check: Pcd=1745.45 kN≥Ru=950.00 kN  ⟹  BUCKLING IS SAFE! (+83.7% margin)P_{cd} = 1745.45\text{ kN} \ge R_u = 950.00\text{ kN} \implies \mathbf{BUCKLING\ IS\ SAFE!\ (+83.7\%\ margin)}

Step 4: Weld Connecting Stiffeners to Web

  • Total available weld length (4 continuous fillet runs): Lw=4(d−2cs)=4(1500−30)=4×1470=5880 mmL_w = 4 (d - 2 c_s) = 4 (1500 - 30) = 4 \times 1470 = 5880\text{ mm}
  • Shear stress per mm: qw=Ru×103Lw=950×1035880=161.56 N/mmq_w = \frac{R_u \times 10^3}{L_w} = \frac{950 \times 10^3}{5880} = \mathbf{161.56\text{ N/mm}}
  • Providing standard 6 mm6\text{ mm} shop fillet weld (s=6 mm,tt=0.7×6=4.2 mm,γmw=1.25s = 6\text{ mm}, t_t = 0.7 \times 6 = 4.2\text{ mm}, \gamma_{mw} = 1.25): qw,cap=ttfu3γmw=4.2×4103×1.25=795.36 N/mmq_{w,cap} = t_t \frac{f_u}{\sqrt{3} \gamma_{mw}} = 4.2 \times \frac{410}{\sqrt{3} \times 1.25} = \mathbf{795.36\text{ N/mm}}
  • Check: qw=161.56 N/mm≤795.36 N/mm  ⟹  WELD IS HIGHLY ADEQUATE!q_w = 161.56\text{ N/mm} \le 795.36\text{ N/mm} \implies \mathbf{WELD\ IS\ HIGHLY\ ADEQUATE!}

Example 3: Flange and Web Splice Design

Problem Statement: A plate girder has a web of 1600 mm×10 mm1600\text{ mm} \times 10\text{ mm} and flanges of 450 mm×30 mm450\text{ mm} \times 30\text{ mm} (fy=250 MPa,fu=410 MPaf_y = 250\text{ MPa}, f_u = 410\text{ MPa}). A field splice is located where the factored bending moment is Mu=3200 kN-mM_u = 3200\text{ kN-m} and factored shear is Vu=600 kNV_u = 600\text{ kN}.

  1. Design the flange splice plates and determine the number of M24 Grade 8.8 bolts (Vdsb=260.87 kNV_{dsb} = 260.87\text{ kN}) for the full tensile capacity.
  2. Determine the portion of bending moment carried by the web MwM_w.

Solution:

Step 1: Section Properties & Moment Distribution

  • Moment of inertia of flanges: hf=d+tf=1600+30=1630 mmh_f = d + t_f = 1600 + 30 = 1630\text{ mm} Iflanges=2[bf⋅tf(hf2)2]=2[450×30×(815)2]=2×13500×664225=17.934×109 mm4I_{flanges} = 2 \left[ b_f \cdot t_f \left(\frac{h_f}{2}\right)^2 \right] = 2 \left[ 450 \times 30 \times (815)^2 \right] = 2 \times 13500 \times 664225 = 17.934 \times 10^9\text{ mm}^4
  • Moment of inertia of web: Iweb=tw⋅d312=10×(1600)312=3.413×109 mm4I_{web} = \frac{t_w \cdot d^3}{12} = \frac{10 \times (1600)^3}{12} = 3.413 \times 10^9\text{ mm}^4
  • Total moment of inertia: Itotal=Iflanges+Iweb=(17.934+3.413)×109=21.347×109 mm4I_{total} = I_{flanges} + I_{web} = (17.934 + 3.413) \times 10^9 = 21.347 \times 10^9\text{ mm}^4
  • Portion of moment carried by flanges: Mflanges=(17.93421.347)×3200=2688.34 kN-m(84.0%)M_{flanges} = \left(\frac{17.934}{21.347}\right) \times 3200 = \mathbf{2688.34\text{ kN-m} \quad (84.0\%)}
  • Portion of moment carried by web: Mweb=(3.41321.347)×3200=511.66 kN-m(16.0%)M_{web} = \left(\frac{3.413}{21.347}\right) \times 3200 = \mathbf{511.66\text{ kN-m} \quad (16.0\%)}

Step 2: Flange Splice Design (Full Plastic Flange Strength)

  • Full plastic tensile/compressive strength of flange: Pf=bf⋅tf⋅fyγm0=450×30×2501.10×103=3068.18 kNP_f = \frac{b_f \cdot t_f \cdot f_y}{\gamma_{m0}} = \frac{450 \times 30 \times 250}{1.10 \times 10^3} = \mathbf{3068.18\text{ kN}}
  • Provide:
    • Outer splice plate: 450 mm×18 mm450\text{ mm} \times 18\text{ mm} (Asp1=8100 mm2A_{sp1} = 8100\text{ mm}^2)
    • Two inner splice plates: 200 mm×18 mm200\text{ mm} \times 18\text{ mm} each (Asp2=2×3600=7200 mm2A_{sp2} = 2 \times 3600 = 7200\text{ mm}^2)
    • Total splice plate area: Asplice=8100+7200=15,300 mm2>Af=450×30=13,500 mm2  ⟹  SAFE!A_{splice} = 8100 + 7200 = 15,300\text{ mm}^2 > A_f = 450 \times 30 = 13,500\text{ mm}^2 \implies \mathbf{SAFE!}
    • Splice plate capacity: Psplice=15300×2501.10×103=3477.27 kN≥3068.18 kN  ⟹  SAFE!P_{splice} = \frac{15300 \times 250}{1.10 \times 10^3} = \mathbf{3477.27\text{ kN}} \ge 3068.18\text{ kN} \implies \mathbf{SAFE!}
  • Bolts required on each side of the flange joint (M24 Gr 8.8 in double shear, Vdsb=260.87 kNV_{dsb} = 260.87\text{ kN}): n=PfVdsb=3068.18260.87=11.76n = \frac{P_f}{V_{dsb}} = \frac{3068.18}{260.87} = 11.76
  • Provide 12 bolts of M24 Grade 8.8 on each side of the joint (arranged in 3 rows of 4 bolts).

Step 3: Web Splice Configuration

  • Provide two web splice plates (one on each side of web):
    • Height =1400 mm= 1400\text{ mm}, thickness tsp=8.0 mmt_{sp} = 8.0\text{ mm} each (2×8=16 mm>tw=10 mm2 \times 8 = 16\text{ mm} > t_w = 10\text{ mm}).
    • Designed to resist concurrent shear Vu=600 kNV_u = 600\text{ kN} and web moment Mw=511.66 kN-mM_w = 511.66\text{ kN-m}.

11. Exam Traps, Common Pitfalls & Practical Fabrication Rules

Trap 1: Confusing Intermediate Stiffener Rigidity with Strength

  • The Trap: Designing intermediate stiffeners purely for axial load capacity without checking the minimum moment of inertia IsI_s.
  • The Reality: If Is<Is,min⁡I_s < I_{s,\min}, the stiffener deflects out of plane alongside the buckled web, failing to create a nodal boundary! The IsI_s condition (0.75dtw30.75 d t_w^3 or 1.5d3tw3/c21.5 d^3 t_w^3 / c^2) is mandatory.

Trap 2: Neglecting the Web Strip in Stiffener Column Checks

  • In both bearing stiffeners and intermediate struts, the effective compression member is NOT just the stiffener plates alone. It is a cruciform/tee section comprising the stiffeners plus an effective web strip of 20tw20 t_w (10tw10 t_w on each side of the stiffener). Neglecting this strip severely underestimates the column buckling capacity.

Trap 3: Position of Longitudinal Stiffeners

  • Frequent Exam Error: Stating that the first longitudinal stiffener is placed at 0.25d0.25 d or 0.33d0.33 d.
  • Standard Specification: IS 800 Cl. 8.7.1 explicitly mandates the first longitudinal stiffener at 0.20d0.20 d from the compression flange, and the second at 0.50d0.50 d (Neutral Axis).

Trap 4: Direct Bearing Contact Snip

  • Bearing stiffeners must be tightly fitted against the flange. However, if the corner is not snipped (coped by 15 to 20 mm15\text{ to }20\text{ mm}), the stiffener rides on the bead of the web-to-flange fillet weld, creating an eccentric point load that induces severe localized weld cracking.

Trap 5: Aligning Flange and Web Splices

  • Catastrophic Site Failure: Placing flange and web splices in the same vertical cross-section creates an unbraced plane of weakness. Always stagger splices by a minimum of 300 mm to 500 mm300\text{ mm to }500\text{ mm}.

12. Official Exam Practice Questions

Question 1 (GATE CE)

According to IS 800:2007, an intermediate transverse stiffener in a plate girder of web depth d=1200 mmd = 1200\text{ mm} and web thickness tw=10 mmt_w = 10\text{ mm} spaced at c=1500 mmc = 1500\text{ mm} must have a minimum second moment of area IsI_s not less than:

  • (A) 900,000 mm4900,000\text{ mm}^4
  • (B) 1,152,000 mm41,152,000\text{ mm}^4
  • (C) 750,000 mm4750,000\text{ mm}^4
  • (D) 1,500,000 mm41,500,000\text{ mm}^4

Detailed Solution:

  • Check aspect ratio: cd=15001200=1.25\frac{c}{d} = \frac{1500}{1200} = 1.25
  • Since c/d=1.25≤2≈1.414c/d = 1.25 \le \sqrt{2} \approx 1.414: Is,min⁡=0.75⋅d⋅tw3=0.75×1200×103=0.75×1200×1000=900,000 mm4I_{s,\min} = 0.75 \cdot d \cdot t_w^3 = 0.75 \times 1200 \times 10^3 = 0.75 \times 1200 \times 1000 = 900,000\text{ mm}^4
  • Correct Answer: (A)

Question 2 (UPSC ESE)

In a welded plate girder, the first horizontal (longitudinal) stiffener is provided at a distance from the compression flange equal to:

  • (A) 0.50d0.50 d
  • (B) 0.20d0.20 d
  • (C) 0.25d0.25 d
  • (D) 0.40d0.40 d

Detailed Solution:

  • The first longitudinal stiffener is provided at 0.20d0.20 d from the compression flange to arrest flexural compressive buckling in the web.
  • Correct Answer: (B)

Question 3 (SSC JE)

The outstand of an unstiffened flat transverse stiffener of thickness tqt_q fabricated from Fe 410 steel shall not exceed:

  • (A) 12tq12 t_q
  • (B) 14tq14 t_q
  • (C) 16tq16 t_q
  • (D) 20tq20 t_q

Detailed Solution:

  • Per IS 800:2007 Cl. 8.7.1.2, the outstand of an unstiffened flat stiffener shall not exceed 14tqϵ14 t_q \epsilon. For Fe 410, ϵ=1.0  ⟹  14tq\epsilon = 1.0 \implies 14 t_q.
  • Correct Answer: (B)

Question 4 (State AE)

When checking an intermediate transverse stiffener as an axial compression member under tension field action, the effective length KLKL is taken as:

  • (A) 1.0d1.0 d
  • (B) 0.85d0.85 d
  • (C) 0.70d0.70 d
  • (D) 0.50d0.50 d

Detailed Solution:

  • Per IS 800:2007 Cl. 8.7.2.4, the effective length of the stiffener strut is taken as 0.70d0.70 d due to the rotational and lateral restraint provided by the heavy flanges.
  • Correct Answer: (C)

Question 5 (UPSC ESE Conventional)

Discuss the functions of bearing stiffeners in a plate girder. Explain why bearing stiffeners are designed for both direct flange bearing and column buckling, and state the effective width of web assumed to act with the stiffener.

Detailed Solution:

  1. Primary Functions:
    • To transfer heavy support reactions or concentrated loads safely into the web without local crushing (web crippling).
    • To act as a vertical column preventing out-of-plane buckling of the web plate at reaction points.
    • To provide torsional end restraint to the girder against twisting at the bearings.
  2. Dual Design Checks:
    • Direct Bearing Check: Stiffener ends are machined/ground to bear directly against the loaded flange. The contact area AbrA_{br} transfers the load directly across the interface. The capacity is checked as Fpsd=Abrfy/(0.8γm0)F_{psd} = A_{br} f_y / (0.8 \gamma_{m0}) to avoid localized yielding of the stiffener toes.
    • Column Buckling Check: The load is then dispersed into the web plate. The combined stiffener-web assembly must have sufficient flexural rigidity about the web axis to act as a compression strut of length 0.70d0.70 d under Buckling Curve c without buckling out of plane.
  3. Effective Web Strip:
    • The code specifies an effective web strip of 20tw20 t_w (10tw10 t_w on either side of the stiffener centerline, or 10tw10 t_w total at an end support) acting compositely with the stiffener plates.