SA-07-04 Chapter 07 · Plastic Analysis of Structures

Plastic Analysis of Portal Frames (Combined & Sway Mechanisms)

Subject
Structural Analysis
Chapter
07 — Plastic Analysis of Structures
Prerequisites
Plastic Hinges & Shape Factor (SA-07-01), Plastic Collapse Theorems & Mechanisms (SA-07-02), Plastic Analysis of Beams (SA-07-03), Slope-Deflection Method for Frames (SA-03-03).
Target Examinations
GATE CE, UPSC ESE, SSC JE, State AE, RRB JE, State JE
Master Directory
civil_/notes/structural_analysis/07_plastic_analysis/04_plastic_analysis_portal_frames.md
In this chapter (4 topics)
On this page

1. Introduction & Conceptual Foundations

Portal frames constitute the primary lateral and gravity load-resisting skeletal system in industrial sheds, warehouses, sports arenas, and low-rise commercial structures. Under elastic design (ASD/WSM), internal forces in portal frames are heavily influenced by foundation fixity, column-to-beam stiffness ratios (Ic/h:Ib/LI_c/h : I_b/L), and thermal/settlement effects.

In contrast, Plastic Analysis evaluates the ultimate capacity of portal frames at impending collapse. In plastic theory:

  1. Elastic stiffness ratios become irrelevant at the plastic limit state; capacity is governed solely by the plastic moment capacities (MpM_p) of the columns and girders.
  2. Foundation settlement and residual stresses do not alter the plastic collapse load (provided ductility is sufficient).
  3. Complex framed structures collapse along one of several distinct kinematic modes: Beam Mechanisms, Sway (Panel) Mechanisms, Joint Mechanisms, or Combined Mechanisms.
   Frame Loading System (Gravity V + Lateral H)
      |
      +---> Beam Mechanism (Span yields under V; lateral sway = 0)
      |
      +---> Sway Mechanism (Columns drift under H; beam does not sag)
      |
      +---> Combined Mechanism (Beam sag + Column drift; Hinge at corner cancels!)
            ===> ALMOST ALWAYS GOVERNS FOR COMBINED GRAVITY + LATERAL LOADS
Portal Frame Plastic Collapse and Interaction Diagram

2. Degrees of Freedom, Indeterminacy & Mechanism Counting

For any planar skeletal frame:

Nm=Np−DsN_m = N_p - D_s

where:

  • DsD_s is the degree of static indeterminacy under planar loading.
  • NpN_p is the number of candidate plastic hinge locations.
  • NmN_m is the dimension of the independent mechanism basis.

2.1 Fixed-Base vs. Pinned-Base Rectangular Portal Frames

Parameter Fixed-Base Portal Frame (Rigid Foundations) Pinned-Base Portal Frame (Two-Hinged Frame)
Support Reactions 6 reactions (HA,VA,MAH_A, V_A, M_A and HD,VD,MDH_D, V_D, M_D) 4 reactions (HA,VAH_A, V_A and HD,VDH_D, V_D)
Static Indeterminacy (DsD_s) Ds=6−3=3D_s = 6 - 3 = \mathbf{3} Ds=4−3=1D_s = 4 - 3 = \mathbf{1}
Hinges at Column Bases Possible (Hinges form at bases A and D) Impossible (Bases are frictionless pins, M=0M = 0)
Total Candidate Hinges (NpN_p) Np=5N_p = 5 (A, B, E, C, D) Np=3N_p = 3 (B, E, C)
Independent Mechanisms (NmN_m) Nm=5−3=2N_m = 5 - 3 = \mathbf{2} Nm=3−1=2N_m = 3 - 1 = \mathbf{2}
Independent Modes 1 Beam Mech + 1 Sway Mech 1 Beam Mech + 1 Sway Mech
Collapse Hinges Needed (NhN_h) Nh=Ds+1=3+1=4N_h = D_s + 1 = 3 + 1 = \mathbf{4} Nh=Ds+1=1+1=2N_h = D_s + 1 = 1 + 1 = \mathbf{2}

3. Independent Mechanism Decomposition for Rectangular Frames

Consider a single-bay rectangular portal frame ABCD with column height hh, beam span LL, carrying horizontal lateral force HH at joint B and concentrated gravity load VV at beam mid-span E.

3.1 Mode 1: Beam Mechanism (NbN_b)

  • Plastic hinges form within the beam: at joint B, mid-span E, and joint C.
  • The columns remain vertical; no lateral displacement occurs (Δh=0\Delta_h = 0).
  • Mid-span deflection: Δv=(L2)θ\Delta_v = \left(\frac{L}{2}\right) \theta.
  • Rotations: θB=θ,θE=2θ,θC=θ\theta_B = \theta, \quad \theta_E = 2\theta, \quad \theta_C = \theta.
  • Work Equation: WE=V⋅(L2θ)W_E = V \cdot \left(\frac{L}{2} \theta\right) WI=MpθB+MpθE+MpθC=Mp(θ+2θ+θ)=4MpθW_I = M_p \theta_B + M_p \theta_E + M_p \theta_C = M_p (\theta + 2\theta + \theta) = 4 M_p \theta Equating WE=WIW_E = W_I: Vc=8MpL(Independent of lateral load H)\mathbf{V_c = \frac{8 M_p}{L}} \quad \text{(Independent of lateral load } H \text{)}

3.2 Mode 2: Sway (Panel) Mechanism (NsN_s)

  • The columns drift laterally by Δh=hθ\Delta_h = h \theta.
  • The beam BC translates as a rigid body without bending (Δv=0\Delta_v = 0).
  • For Fixed Bases: Plastic hinges form at A, B, C, and D: WE=H⋅(hθ)W_E = H \cdot (h \theta) WI=Mp(θA+θB+θC+θD)=Mp(θ+θ+θ+θ)=4MpθW_I = M_p (\theta_A + \theta_B + \theta_C + \theta_D) = M_p (\theta + \theta + \theta + \theta) = 4 M_p \theta Hc=4Mph(Fixed Base)\mathbf{H_c = \frac{4 M_p}{h}} \quad \text{(Fixed Base)}
  • For Pinned Bases: Plastic hinges form only at column tops B and C (bases A and D rotate freely): WE=H⋅(hθ)W_E = H \cdot (h \theta) WI=Mp(θB+θC)=Mp(θ+θ)=2MpθW_I = M_p (\theta_B + \theta_C) = M_p (\theta + \theta) = 2 M_p \theta Hc=2Mph(Pinned Base)\mathbf{H_c = \frac{2 M_p}{h}} \quad \text{(Pinned Base)}

4. Combined Mechanisms & The Principle of Corner Hinge Cancellation

When a frame is subjected simultaneously to lateral wind/seismic load HH and vertical gravity load VV, the beam mechanism and sway mechanism interact kinematically.

4.1 Kinematic Superposition & Corner Cancellation

  1. In the Sway Mechanism: Column AB rotates clockwise by +θ+\theta. This causes the top of column AB at joint B to rotate clockwise by +θ+\theta.
  2. In the Beam Mechanism: Segment BE rotates counter-clockwise by −θ-\theta to accommodate mid-span downward sag.
  3. At the rigid corner joint B: θB,net=θsway−θbeam=θ−θ=0\theta_{B,\text{net}} = \theta_{\text{sway}} - \theta_{\text{beam}} = \theta - \theta = \mathbf{0} The plastic hinge at joint B completely vanishes!
  4. At the opposite corner joint C: θC,net=θsway+θbeam=θ+θ=2θ\theta_{C,\text{net}} = \theta_{\text{sway}} + \theta_{\text{beam}} = \theta + \theta = \mathbf{2\theta} The hinge rotations reinforce each other.

4.2 Energy Dissipation in the Combined Mechanism (Fixed Base)

  • Plastic hinges form at: Base A (θ\theta), Mid-span E (2θ2\theta), Corner C (2θ2\theta), Base D (θ\theta).
  • Total Internal Plastic Work: WI=Mp(θA+θE+θC+θD)=Mp(θ+2θ+2θ+θ)=6MpθW_I = M_p (\theta_A + \theta_E + \theta_C + \theta_D) = M_p (\theta + 2\theta + 2\theta + \theta) = \mathbf{6 M_p \theta} (Notice that without cancellation, WIW_I would have been 8Mpθ8 M_p \theta. Cancellation saves 2Mpθ2 M_p \theta of plastic work!)
  • Total External Work: WE=H⋅Δh+V⋅Δv=H(hθ)+V(L2θ)=[Hh+VL2]θW_E = H \cdot \Delta_h + V \cdot \Delta_v = H (h \theta) + V \left(\frac{L}{2} \theta\right) = \left[ H h + V \frac{L}{2} \right] \theta
  • Virtual Work Balance: H⋅h+V⋅L2=6Mp(Fixed Base Combined Mechanism)\mathbf{H \cdot h + V \cdot \frac{L}{2} = 6 M_p} \quad \text{(Fixed Base Combined Mechanism)}
  • For a Pinned-Base Frame (no hinges at A and D): WI=MpθE+MpθC=Mp(2θ+2θ)=4MpθW_I = M_p \theta_E + M_p \theta_C = M_p (2\theta + 2\theta) = 4 M_p \theta H⋅h+V⋅L2=4Mp(Pinned Base Combined Mechanism)\mathbf{H \cdot h + V \cdot \frac{L}{2} = 4 M_p} \quad \text{(Pinned Base Combined Mechanism)}

5. Mechanism Interaction Diagrams (Failure Envelopes)

The safe load domain for a portal frame subjected to independent variable loads HH and VV is represented in a two-dimensional Mechanism Interaction Diagram:

  • Horizontal Axis: Normalized lateral load Hˉ=HhMp\bar{H} = \frac{H h}{M_p}.
  • Vertical Axis: Normalized gravity load Vˉ=VLMp\bar{V} = \frac{V L}{M_p}.

5.1 Boundary Equations (Fixed-Base Frame)

  1. Beam Boundary: Vˉ≤8.0(Horizontal line)\bar{V} \le 8.0 \quad (\text{Horizontal line})
  2. Sway Boundary: Hˉ≤4.0(Vertical line)\bar{H} \le 4.0 \quad (\text{Vertical line})
  3. Combined Boundary: Hˉ+0.5Vˉ≤6.0  ⟹  Vˉ≤12.0−2Hˉ(Sloping line)\bar{H} + 0.5 \bar{V} \le 6.0 \implies \bar{V} \le 12.0 - 2 \bar{H} \quad (\text{Sloping line})

5.2 Geometry of the Failure Envelope

  • When Vˉ=8.0\bar{V} = 8.0: Hˉ=6.0−0.5(8.0)=2.0\bar{H} = 6.0 - 0.5(8.0) = \mathbf{2.0}.
  • When Hˉ=4.0\bar{H} = 4.0: Vˉ=2(6.0−4.0)=4.0\bar{V} = 2(6.0 - 4.0) = \mathbf{4.0}.
  • The failure envelope forms a convex polygon connecting vertices: (0,0)→(0,8.0)→(2.0,8.0)→(4.0,4.0)→(4.0,0)(0, 0) \to (0, 8.0) \to (2.0, 8.0) \to (4.0, 4.0) \to (4.0, 0)
  • Convexity Postulate (Drucker's Stability Postulate): The failure surface in load space is strictly convex. Any point inside the polygon represents a statically safe state. Any point outside represents plastic collapse.

6. Pitched-Roof (Gable) Portal Frames: Instantaneous Center Method

Pitched-roof (gable) frames introduce non-orthogonal geometry where rafters slope upwards toward a central apex (ridge point C).

                      Ridge C (Apex)
                         /\
           Rafter BC    /  \    Rafter CD
                       /    \
            Eaves B +--      --+ Eaves D
                    |          |
          Column AB |          | Column DE
                    |          |
            Base A /|/|/    /|/|/ Base E
Gable Frame Plastic Collapse and Instantaneous Center Method

6.1 The Instantaneous Center of Rotation (IC)

In a gable collapse mechanism, rafters BC and CD undergo general planar motion (simultaneous translation and rotation). To relate linear displacements of load points to angular hinge rotations, the Instantaneous Center of Rotation (ICIC) is determined:

  • The base of column AB rotates about fixed foundation A   ⟹  \implies Joint B moves horizontally to the right: ΔB,h=h⋅θ\Delta_{B,h} = h \cdot \theta
  • By symmetry under vertical ridge loading, the ridge point C moves strictly vertically downward: ΔC,h=0,ΔC,v=Δv\Delta_{C,h} = 0, \quad \Delta_{C,v} = \Delta_v
  • Locating IC1IC_1 for Rafter BC:
    1. Draw a line perpendicular to the displacement vector of B (a vertical line through joint B).
    2. Draw a line perpendicular to the displacement vector of C (a horizontal line through ridge C).
    3. The intersection point of these two perpendiculars is the Instantaneous Center (IC1IC_1): Coordinates of IC1:x=xB=0,y=yC=h+r\text{Coordinates of } IC_1: \quad x = x_B = 0, \quad y = y_C = h + r where hh is column height and rr is roof rise (r=Hridge−hr = H_{\text{ridge}} - h).

6.2 Kinematic Relations via ICIC

  • Distance from IC1IC_1 to Joint B: rB=yC−yB=(h+r)−h=r(Rise of roof)r_B = y_C - y_B = (h + r) - h = \mathbf{r} \quad (\text{Rise of roof})
  • Distance from IC1IC_1 to Ridge C: rC=xC−xB=b(Half-span of frame)r_C = x_C - x_B = \mathbf{b} \quad (\text{Half-span of frame})
  • Angular rotation of rafter BC (θrafter\theta_{\text{rafter}}): θrafter=ΔB,hrB=h⋅θr\theta_{\text{rafter}} = \frac{\Delta_{B,h}}{r_B} = \frac{h \cdot \theta}{r}
  • Vertical downward displacement of apex C (Δv\Delta_v): Δv=rC⋅θrafter=b⋅(hθr)=(bhr)θ\Delta_v = r_C \cdot \theta_{\text{rafter}} = b \cdot \left(\frac{h \theta}{r}\right) = \mathbf{\left(\frac{b h}{r}\right) \theta}

6.3 Work Balance for Gable Frame under Ridge Load WW

  • External Work: WE=W⋅Δv=W(bhr)θW_E = W \cdot \Delta_v = W \left(\frac{b h}{r}\right) \theta
  • Hinge Rotations:
    • Fixed base A: θA=θ\theta_A = \theta
    • Eaves B: θB=θcolumn+θrafter=θ+hrθ=θ(1+hr)\theta_B = \theta_{\text{column}} + \theta_{\text{rafter}} = \theta + \frac{h}{r}\theta = \theta \left(1 + \frac{h}{r}\right)
    • Apex C: θC=2θrafter=2(hr)θ\theta_C = 2 \theta_{\text{rafter}} = 2 \left(\frac{h}{r}\right) \theta
    • By symmetry: θD=θ(1+hr),θE=θ\theta_D = \theta \left(1 + \frac{h}{r}\right), \quad \theta_E = \theta
  • Total Internal Work: WI=Mp[θA+θB+θC+θD+θE]=Mp[2θ+2θ(1+hr)+2hrθ]=Mpθ[4+4hr]W_I = M_p \left[ \theta_A + \theta_B + \theta_C + \theta_D + \theta_E \right] = M_p \left[ 2\theta + 2\theta\left(1 + \frac{h}{r}\right) + 2\frac{h}{r}\theta \right] = \mathbf{M_p \theta \left[ 4 + 4 \frac{h}{r} \right]}
  • Collapse Load: Wc(bhr)θ=4Mpθ(r+hr)  ⟹  Wc=4Mp(h+r)bhW_c \left(\frac{b h}{r}\right) \theta = 4 M_p \theta \left( \frac{r + h}{r} \right) \implies \mathbf{W_c = \frac{4 M_p (h + r)}{b h}}

7. Worked Numerical Examples

Problem 1: Pinned-Base (Two-Hinged) Portal Frame (Beam vs. Sway vs. Combined)

Statement: A rectangular two-hinged portal frame ABCD has pinned bases at A and D (MA=0,MD=0M_A = 0, M_D = 0). Column height h=4.0 mh = 4.0\text{ m}, beam span L=6.0 mL = 6.0\text{ m}. Plastic moment capacity Mp=60.0 kNmM_p = 60.0\text{ kNm} is uniform throughout. The frame carries a horizontal lateral load H=PH = P at joint B and a concentrated vertical load V=1.5PV = 1.5 P at the center of beam BC (point E).

  1. Calculate the collapse load PP for the Beam Mechanism.
  2. Calculate the collapse load PP for the Sway Mechanism.
  3. Calculate the collapse load PP for the Combined Mechanism.
  4. Determine the true collapse load PcP_c and verify that the unyielded joint B does not violate the yield condition.

Solution:

Step 1: Mechanism 1 — Beam Mechanism

  • Hinges form at joint B, mid-span E, and joint C:
    • Columns remain vertical: Δh=0\Delta_h = 0.
    • Deflection under load VV: Δv=(L/2)θ=3.0θ\Delta_v = (L/2) \theta = 3.0 \theta.
    • Rotations: θB=θ,θE=2θ,θC=θ\theta_B = \theta, \quad \theta_E = 2\theta, \quad \theta_C = \theta.
    • WE=V⋅Δv=(1.5P)⋅(3.0θ)=4.5PθW_E = V \cdot \Delta_v = (1.5 P) \cdot (3.0\theta) = 4.5 P \theta.
    • WI=Mp(θ+2θ+θ)=4.0MpθW_I = M_p (\theta + 2\theta + \theta) = 4.0 M_p \theta.
    • Equating WE=WIW_E = W_I: 4.5Pθ=4.0Mpθ  ⟹  Pc1=4.04.5Mp=89Mp4.5 P \theta = 4.0 M_p \theta \implies P_{c1} = \frac{4.0}{4.5} M_p = \frac{8}{9} M_p
    • For Mp=60.0 kNmM_p = 60.0\text{ kNm}: Pc1=89×60.0=53.3333 kNP_{c1} = \frac{8}{9} \times 60.0 = \mathbf{53.3333\text{ kN}}

Step 2: Mechanism 2 — Sway Mechanism

  • Frame sways rightward by Δh=hθ=4.0θ\Delta_h = h \theta = 4.0 \theta.
  • Bases A and D are real pins (M=0M = 0); hinges form only at column tops B and C:
    • Rotations: θB=θ,θC=θ\theta_B = \theta, \quad \theta_C = \theta.
    • WE=H⋅Δh=P⋅(4.0θ)=4.0PθW_E = H \cdot \Delta_h = P \cdot (4.0\theta) = 4.0 P \theta.
    • WI=Mp(θB+θC)=Mp(θ+θ)=2.0MpθW_I = M_p (\theta_B + \theta_C) = M_p (\theta + \theta) = 2.0 M_p \theta.
    • Equating WE=WIW_E = W_I: 4.0Pθ=2.0Mpθ  ⟹  Pc2=2.04.0Mp=0.50Mp4.0 P \theta = 2.0 M_p \theta \implies P_{c2} = \frac{2.0}{4.0} M_p = 0.50 M_p
    • For Mp=60.0 kNmM_p = 60.0\text{ kNm}: Pc2=0.50×60.0=30.0000 kNP_{c2} = 0.50 \times 60.0 = \mathbf{30.0000\text{ kN}}

Step 3: Mechanism 3 — Combined Mechanism

  • Sway rotation (+θ)(+\theta) and beam rotation (−θ)(-\theta) cancel each other at corner joint B (θB,net=0\theta_{B,\text{net}} = 0).
  • Plastic hinges form at:
    • Mid-span E: θE=2θ\theta_E = 2\theta
    • Corner C: θC=θbeam+θsway=θ+θ=2θ\theta_C = \theta_{\text{beam}} + \theta_{\text{sway}} = \theta + \theta = 2\theta
  • External Work: WE=H⋅Δh+V⋅Δv=P(4.0θ)+(1.5P)(3.0θ)=4.0Pθ+4.5Pθ=8.5PθW_E = H \cdot \Delta_h + V \cdot \Delta_v = P (4.0\theta) + (1.5P) (3.0\theta) = 4.0 P \theta + 4.5 P \theta = \mathbf{8.5 P \theta}
  • Internal Plastic Work: WI=MpθE+MpθC=Mp(2θ)+Mp(2θ)=4.0MpθW_I = M_p \theta_E + M_p \theta_C = M_p (2\theta) + M_p (2\theta) = \mathbf{4.0 M_p \theta}
  • Equating WE=WIW_E = W_I: 8.5Pθ=4.0Mpθ  ⟹  Pc3=4.08.5Mp=817Mp≈0.470588Mp8.5 P \theta = 4.0 M_p \theta \implies P_{c3} = \frac{4.0}{8.5} M_p = \frac{8}{17} M_p \approx \mathbf{0.470588 M_p}
  • For Mp=60.0 kNmM_p = 60.0\text{ kNm}: Pc3=817×60.0=28.2353 kNP_{c3} = \frac{8}{17} \times 60.0 = \mathbf{28.2353\text{ kN}}

Step 4: Governing Collapse Load & Statics Verification at Joint B

Pc=min⁡(53.3333,30.0000,28.2353)=28.2353 kNP_c = \min(53.3333, 30.0000, 28.2353) = \mathbf{28.2353\text{ kN}}

The Combined Mechanism governs at Pc=28.2353 kNP_c = 28.2353\text{ kN}.

Statics Check at Unyielded Joint B:

  • Column CD: Hinge at top C (MC=Mp=60.0 kNmM_C = M_p = 60.0\text{ kNm}), base D is pinned (MD=0M_D = 0). HCD=MCh=60.04.0=15.0000 kNH_{CD} = \frac{M_C}{h} = \frac{60.0}{4.0} = 15.0000\text{ kN}
  • Horizontal equilibrium of the entire frame: ∑Fx=0  ⟹  HAB+HCD=Pc\sum F_x = 0 \implies H_{AB} + H_{CD} = P_c HAB+15.0000=28.2353  ⟹  HAB=13.2353 kNH_{AB} + 15.0000 = 28.2353 \implies H_{AB} = 13.2353\text{ kN}
  • Column AB (pinned base A, MA=0M_A = 0): MB=HAB⋅h=13.2353×4.0=52.9412 kNmM_B = H_{AB} \cdot h = 13.2353 \times 4.0 = \mathbf{52.9412\text{ kNm}}
  • Check Yield Condition: ∣MB∣=52.9412 kNm<Mp=60.0000 kNm|M_B| = 52.9412\text{ kNm} < M_p = 60.0000\text{ kNm} The bending moment at joint B is 88.24%88.24\% of MpM_p, strictly satisfying the yield criterion! Therefore, by the Uniqueness Theorem, Pc=28.2353 kNP_c = 28.2353\text{ kN} is the exact collapse load.

Problem 2: Fixed Portal Frame with Unequal Column Heights

Statement: A rectangular portal frame ABCD has fixed bases at A and D. Column AB has height h1=4.0 mh_1 = 4.0\text{ m}, while column CD has height h2=6.0 mh_2 = 6.0\text{ m}. Beam BC has span L=6.0 mL = 6.0\text{ m}. Plastic capacity Mp=100.0 kNmM_p = 100.0\text{ kNm} is uniform throughout. A lateral load H=PH = P acts at joint B, and a vertical load V=2PV = 2P acts at mid-span of beam BC. Determine the governing plastic collapse load PcP_c.

Solution:

Step 1: Mechanism Kinematics with Unequal Columns

  • Let column AB rotate by θ1\theta_1.
  • Lateral sway at joint B: Δh=h1θ1=4.0θ1\Delta_h = h_1 \theta_1 = 4.0 \theta_1.
  • Since beam BC is axially rigid, joint C sways by the identical horizontal distance: Δh=4.0θ1\Delta_h = 4.0 \theta_1.
  • Column CD has height h2=6.0 mh_2 = 6.0\text{ m}, so its rotation θ2\theta_2 is: θ2=Δhh2=4.0θ16.0=23θ1\theta_2 = \frac{\Delta_h}{h_2} = \frac{4.0 \theta_1}{6.0} = \frac{2}{3} \theta_1

Step 2: Mode 1 — Sway Mechanism

  • Hinges at A, B, C, D:
    • Rotations: θA=θ1,θB=θ1,θC=θ2=23θ1,θD=θ2=23θ1\theta_A = \theta_1, \quad \theta_B = \theta_1, \quad \theta_C = \theta_2 = \frac{2}{3}\theta_1, \quad \theta_D = \theta_2 = \frac{2}{3}\theta_1.
  • Work Equation: WE=P⋅Δh=P⋅(4.0θ1)=4.0Pθ1W_E = P \cdot \Delta_h = P \cdot (4.0 \theta_1) = 4.0 P \theta_1 WI=Mp[θ1+θ1+23θ1+23θ1]=Mp(2+43)θ1=103Mpθ1W_I = M_p \left[ \theta_1 + \theta_1 + \frac{2}{3}\theta_1 + \frac{2}{3}\theta_1 \right] = M_p \left( 2 + \frac{4}{3} \right) \theta_1 = \frac{10}{3} M_p \theta_1 4.0Pθ1=103Mpθ1  ⟹  Pc,sway=1012Mp=56Mp=83.3333 kN4.0 P \theta_1 = \frac{10}{3} M_p \theta_1 \implies P_{c,\text{sway}} = \frac{10}{12} M_p = \frac{5}{6} M_p = \mathbf{83.3333\text{ kN}}

Step 3: Mode 2 — Beam Mechanism

  • Mid-span deflection: Δv=(L/2)θ=3.0θ\Delta_v = (L/2) \theta = 3.0 \theta.
  • Rotations: θB=θ,θE=2θ,θC=θ\theta_B = \theta, \quad \theta_E = 2\theta, \quad \theta_C = \theta.
  • Work Equation: WE=(2P)⋅(3.0θ)=6.0PθW_E = (2P) \cdot (3.0\theta) = 6.0 P \theta WI=4.0Mpθ  ⟹  Pc,beam=46Mp=23Mp=66.6667 kNW_I = 4.0 M_p \theta \implies P_{c,\text{beam}} = \frac{4}{6} M_p = \frac{2}{3} M_p = \mathbf{66.6667\text{ kN}}

Step 4: Mode 3 — Combined Mechanism

  • Corner joint B cancels: θsway−θbeam=0  ⟹  θ1=θ\theta_{\text{sway}} - \theta_{\text{beam}} = 0 \implies \theta_1 = \theta.
  • Column CD rotates by θ2=23θ\theta_2 = \frac{2}{3}\theta.
  • Hinge rotations:
    • Base A: θA=θ1=θ\theta_A = \theta_1 = \theta
    • Mid-span E: θE=2θ\theta_E = 2\theta
    • Corner C: θC=θbeam+θ2=θ+23θ=53θ\theta_C = \theta_{\text{beam}} + \theta_2 = \theta + \frac{2}{3}\theta = \frac{5}{3}\theta
    • Base D: θD=θ2=23θ\theta_D = \theta_2 = \frac{2}{3}\theta
  • External Work: WE=P(4.0θ)+(2P)(3.0θ)=4.0Pθ+6.0Pθ=10.0PθW_E = P (4.0\theta) + (2P)(3.0\theta) = 4.0 P \theta + 6.0 P \theta = \mathbf{10.0 P \theta}
  • Internal Plastic Work: WI=Mp[θ+2θ+53θ+23θ]=Mp(3+73)θ=163MpθW_I = M_p \left[ \theta + 2\theta + \frac{5}{3}\theta + \frac{2}{3}\theta \right] = M_p \left( 3 + \frac{7}{3} \right) \theta = \frac{16}{3} M_p \theta
  • Equating WE=WIW_E = W_I: 10.0Pθ=163Mpθ  ⟹  Pc=1630Mp=815Mp≈0.533333Mp10.0 P \theta = \frac{16}{3} M_p \theta \implies P_c = \frac{16}{30} M_p = \frac{8}{15} M_p \approx \mathbf{0.533333 M_p}
  • For Mp=100.0 kNmM_p = 100.0\text{ kNm}: Pc=815×100.0=53.3333 kNP_c = \frac{8}{15} \times 100.0 = \mathbf{53.3333\text{ kN}}
  • Governing Mode: Combined mechanism governs with collapse load Pc=53.3333 kNP_c = \mathbf{53.3333\text{ kN}}.

Problem 3: Pitched-Roof (Gable) Portal Frame under Vertical Ridge Load

Statement: A symmetrical gable portal frame ABCDE with fixed bases at A and E has:

  • Column height h=4.0 mh = 4.0\text{ m} (columns AB and ED).
  • Frame span L=8.0 mL = 8.0\text{ m} (half span b=4.0 mb = 4.0\text{ m}).
  • Ridge / apex C at height H=6.0 mH = 6.0\text{ m} (roof rise r=6.0−4.0=2.0 mr = 6.0 - 4.0 = 2.0\text{ m}).
  • Uniform plastic moment capacity Mp=120.0 kNmM_p = 120.0\text{ kNm}. A concentrated vertical load WW is applied at the ridge point C. Using the Instantaneous Center of Rotation method, compute the collapse load WcW_c.

Solution:

Step 1: Geometry of the Instantaneous Center (ICIC)

  • By symmetry, eaves B and D spread outwards horizontally while ridge C drops vertically.
  • Let column sway angle be θ\theta. Horizontal displacement at eaves B: ΔB,h=h⋅θ=4.0θ\Delta_{B,h} = h \cdot \theta = 4.0 \theta
  • Normal to displacement at B is a vertical line at x=0x = 0.
  • Normal to vertical displacement at C is a horizontal line at y=h+r=6.0 my = h + r = 6.0\text{ m}.
  • The intersection gives IC1IC_1 of rafter BC at (0,6.0 m)(0, 6.0\text{ m}):
    • Arm to joint B: rB=yIC−yB=6.0−4.0=2.0 m=rr_B = y_{IC} - y_B = 6.0 - 4.0 = 2.0\text{ m} = r.
    • Arm to ridge C: rC=xC−xIC=4.0−0=4.0 m=br_C = x_C - x_{IC} = 4.0 - 0 = 4.0\text{ m} = b.

Step 2: Angular Rotation and Ridge Displacement

  • Rafter rotation: θrafter=ΔB,hrB=4.0θ2.0=2.0θ\theta_{\text{rafter}} = \frac{\Delta_{B,h}}{r_B} = \frac{4.0 \theta}{2.0} = \mathbf{2.0 \theta}
  • Vertical downward displacement of ridge C (Δv\Delta_v): Δv=rC⋅θrafter=4.0×(2.0θ)=8.0θ\Delta_v = r_C \cdot \theta_{\text{rafter}} = 4.0 \times (2.0 \theta) = \mathbf{8.0 \theta}

Step 3: Internal Plastic Work (WIW_I) Hinges form at all five critical sections (A, B, C, D, E):

  • Base A: θA=θ\theta_A = \theta
  • Eaves B: θB=θcolumn+θrafter=θ+2.0θ=3.0θ\theta_B = \theta_{\text{column}} + \theta_{\text{rafter}} = \theta + 2.0\theta = 3.0\theta
  • Apex C: Both rafters rotate by θrafter  ⟹  θC=2.0θ+2.0θ=4.0θ\theta_{\text{rafter}} \implies \theta_C = 2.0\theta + 2.0\theta = 4.0\theta
  • Eaves D: θD=3.0θ\theta_D = 3.0\theta (by symmetry)
  • Base E: θE=θ\theta_E = \theta (by symmetry)
  • Total Internal Work: WI=Mp(θA+θB+θC+θD+θE)=Mp(θ+3θ+4θ+3θ+θ)=12.0MpθW_I = M_p (\theta_A + \theta_B + \theta_C + \theta_D + \theta_E) = M_p (\theta + 3\theta + 4\theta + 3\theta + \theta) = \mathbf{12.0 M_p \theta}

Step 4: External Work & Collapse Load

WE=Wc⋅Δv=Wc⋅(8.0θ)W_E = W_c \cdot \Delta_v = W_c \cdot (8.0 \theta)

Equating WE=WIW_E = W_I:

Wc⋅(8.0θ)=12.0Mpθ  ⟹  Wc=12.08.0Mp=1.5000MpW_c \cdot (8.0 \theta) = 12.0 M_p \theta \implies W_c = \frac{12.0}{8.0} M_p = \mathbf{1.5000 M_p}

Substituting Mp=120.0 kNmM_p = 120.0\text{ kNm}:

Wc=1.5000×120.0=180.0000 kNW_c = 1.5000 \times 120.0 = \mathbf{180.0000\text{ kN}}

8. Common Misconceptions & Exam Pitfalls

[!CAUTION]

  1. Assuming Sway Always Governs over Combined: For frames carrying both lateral and vertical loads, neither the pure sway nor pure beam mechanism governs. The Combined Mechanism almost always produces the lowest collapse load factor due to the corner hinge cancellation!
  2. Neglecting Instantaneous Centers in Gable Frames: Rafters in pitched-roof frames undergo rigid-body planar rotation about their instantaneous centers, not simple rotation about the eaves. Assuming Δv=bθ\Delta_v = b \theta without dividing by rise rr produces massive dimensional errors.
  3. Pinned Bases vs Fixed Bases in Sway: In a pinned-base frame, no hinges form at the foundations (MA=MD=0M_A = M_D = 0). Internal work for sway is 2Mpθ2 M_p \theta (not 4Mpθ4 M_p \theta).
  4. Unequal Column Heights: When columns have different heights h1≠h2h_1 \neq h_2, the lateral drift Δh\Delta_h is the same, but the angular rotations differ (θ1=Δ/h1≠θ2=Δ/h2\theta_1 = \Delta/h_1 \neq \theta_2 = \Delta/h_2). You must relate both rotations to a single reference parameter.

9. Comparative Summary & Formula Matrix

Frame Configuration Loading Condition Governing Mechanism Equation Collapse Load Factor (PcP_c)
Fixed Rectangular Mid-span Vertical VV only V(L/2)θ=4MpθV (L/2) \theta = 4 M_p \theta Vc=8Mp/LV_c = 8 M_p / L
Fixed Rectangular Top Lateral HH only Hhθ=4MpθH h \theta = 4 M_p \theta Hc=4Mp/hH_c = 4 M_p / h
Fixed Rectangular Combined HH and VV Hh+V(L/2)=6MpH h + V (L/2) = 6 M_p Interaction Line
Pinned Rectangular Top Lateral HH only Hhθ=2MpθH h \theta = 2 M_p \theta Hc=2Mp/hH_c = 2 M_p / h
Pinned Rectangular Combined HH and VV Hh+V(L/2)=4MpH h + V (L/2) = 4 M_p Interaction Line
Fixed Gable Frame Vertical Ridge Load WW W(bhr)=4Mp(1+hr)W \left(\frac{b h}{r}\right) = 4 M_p \left(1 + \frac{h}{r}\right) Wc=4Mp(h+r)bhW_c = \frac{4 M_p (h + r)}{b h}

10. Practice Questions & Competitive Examination Problems

Multiple Choice & Objective Questions

  1. [GATE CE] In a rectangular single-bay portal frame with fixed bases subjected to a lateral load HH and a gravity load VV, the number of plastic hinges required for complete collapse in the combined mechanism is:

    • (A) 3
    • (B) 4
    • (C) 5
    • (D) 6
      Answer: (B) Ds=3  ⟹  Nh=Ds+1=4D_s = 3 \implies N_h = D_s + 1 = 4 hinges (at base A, mid-span E, corner C, base D; hinge at B cancels).
  2. [ESE CE] A two-hinged rectangular portal frame has column height hh and plastic moment capacity MpM_p. Under a horizontal load HH at the top, the plastic collapse load HcH_c is:

    • (A) Mp/hM_p / h
    • (B) 2Mp/h2 M_p / h
    • (C) 4Mp/h4 M_p / h
    • (D) 6Mp/h6 M_p / h
      Answer: (B) H⋅hθ=2Mpθ  ⟹  Hc=2Mp/hH \cdot h \theta = 2 M_p \theta \implies H_c = 2 M_p / h.
  3. [SSC JE] In a plastic collapse mechanism of a rigid frame, when a beam mechanism is added to a sway mechanism, the plastic hinge at the leeward corner joint:

    • (A) Cancels out
    • (B) Doubles in rotation (θ+θ=2θ\theta + \theta = 2\theta)
    • (C) Halves in rotation
    • (D) Has zero moment
      Answer: (B) The rotations reinforce each other at the leeward joint (θC=2θ\theta_C = 2\theta), whereas at the windward joint they cancel (θB=0\theta_B = 0).
  4. [State AE] The Instantaneous Center of Rotation method is primarily used in the plastic analysis of:

    • (A) Simply supported beams
    • (B) Pitched-roof (gable) portal frames
    • (C) Prismatic columns
    • (D) Circular rings
      Answer: (B) Pitched-roof (gable) portal frames.

11. References & Code Standards

  • IS 800:2007: General Construction in Steel — Code of Practice, Section 12 (Plastic Design), Bureau of Indian Standards.
  • AISC 360-16: Specification for Structural Steel Buildings, Appendix 1 (Design by Inelastic Analysis).
  • Eurocode 3 (EN 1993-1-1): Design of Steel Structures — Part 1-1: General Rules and Rules for Buildings.
  • Baker, J. F., Horne, M. R., & Heyman, J. (1956). The Steel Skeleton: Volume II, Plastic Behaviour and Design. Cambridge University Press.
  • Neal, B. G. (1977). The Plastic Methods of Structural Analysis. Chapman and Hall.
About this page’s source
Topic ID
SA-07-04 (from metadata/sync_topic.py MAPPINGS)
Source file
notes/structural_analysis/07_plastic_analysis/04_plastic_analysis_portal_frames.md
Presentation changes
  • Leading title heading and bold Key: value metadata lines shown in the page header instead of the body
  • Display-math fences normalised at render time (62 block(s); TeX unchanged)